STEP 4: CHECK OUT YOUR DOOR OPERATING SYSTEM
CAUTION: THERE ARE NO USER SERVICEABLE PARTS INSIDETRANSMITTER OR RECEIVERA.After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 35 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable.
B.If the transmitter doesn’t activate the operator, check the coding switches on both the transmitter and receiver to assure an “exact” match. (See Fig. 2 & 3). This may necessitate a reprogramming of a Quik Code Classic transmitter to match the receiver coding switches.
C.If the distance is inadequate, check the battery and replace if necessary. (Also See
Step 4D).D.To maximize the operating distance move the transmitter to different locations in the car until a satisfactory distance is achieved.
E.If the receiver is in the proximity of a metal beam or other obstruction it may be necessary to relocate the receiver to increase the operating range.
F.If multiple receivers are mounted closer than 15 feet, blocking and interference may occur. Relocate the receivers farther apart.
G.If system does not work at any distance, check that the receiver terminals are connected to the proper operator terminals. See Step 2A.
Manufacturer’s Limited Warranty
Installation Instructions
Garage Door and Gate Operator Radio Controls
Models 9921, 9931, 8822, 8832, 8833
Proper installation of your radio controls will assure
years of trouble-free operation.
READ THE FOLLOWING INSTRUCTIONSTHOROUGHLY BEFORE STARTING INSTALLATIONSTEP 1: SET YOUR CODING SWITCHES
CAUTION: THE FACTORY PRESET CODE MUST BE
CHANGED TO SAFEGUARD AGAINST UNAUTHORIZED
OPERATION.
Allstar warrants its radio controls to be free from defect in material and workmanship for a period of one (1) year from the date of purchase. To obtain service, contact your dealer.
To obtain service under this warranty the buyer must obtain authorization instructions for the
return of any goods from Allstar before returning the goods. The goods must be returned with
complete identification, with copy of
Goods returned to Allstar for warranty repair within the warranty period, which upon receipt by Allstar are confirmed to be defective and covered by this limited warranty, will be repaired or replaced at Allstar’s sole option, at no cost and returned
repaired or replaced with new or factory rebuilt parts at Allstar’s sole option.
This limited warranty does not cover
These warranties are in lieu of all other warranties, either expressed or implied. All implied
warranties of merchantability and/or fitness for a particular purpose are hereby disclaimed and
excluded. Under no circumstances shall Allstar be liable for consequential, incidental or special damages arising in connection with the use or inability to use this product. In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar
104384
TRANSMITTER
Figure 1A
104385
RECEIVER
Figure 1B
A.Remove the access cover from the front of the transmitter by sliding the cover away from the top of the transmitter. (See Fig. 1A).
B.Use a small screwdriver or knife to remove small door on back of receiver to gain access to coding switches. (See Fig. 1B)
IMPORTANT: THE EXACT SAME CODE MUST BE SET ON BOTH THE TRANSMITTER AND RECEIVER. IF JUST ONE SWITCH IS MISMATCHED THE CONTROLS WILL NOT FUNCTION.
any other liability in connection with the sale of this product.
This warranty gives you specific legal rights. You may also have other rights which vary from
state to state. Warranty effective after July 1, 1998.
For Information:
|
| Phone |
| info@allstarcorp.com |
|
| |
|
|
| FAX |
| www.allstarcorp.com |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Note: If installing Allstar Classic Quik Code transmitter(s) with a 99xx or 88xx Allstar Receiver, first set your receiver coding switches to your private code setting using the instructions that follow THEN program your Allstar Classic Quik Code transmitter (following the instructions included with the transmitter) to match the receiver.
PART #107713 REV C