Allstar Products Group 9931T installation instructions Operational Check, Replacement for Models

Operational Check

After installing your receiver and transmitter, check the operation of your radio controls by moving approximately 45 feet back from the garage door, then press the transmitter button. Operation at this distance should be reliable. However, environmental conditions and the location of the transmitter and receiver will affect distance.

•If the transmitter doesn’t activate the operator check the coding on both the transmitter and receiver. The code setting must match exactly .

•If the distance is inadequate check the battery and replace if necessary.

•To maximize the operating distance move the transmitter to different locations in the car until a satisfactory distance is achieved. Vanity mirrors on sun visors will affect performance.

•If the receiver is in the proximity of a metal beam or other obstruction it may be necessary to relocate the receiver to increase the operating range.

•If multiple receivers are mounted closer than 15 feet, blocking and interference may occur. Move the receivers further apart.

•If system does not work at any distance, check that the receiver terminals are connected to the proper operator terminals.

•If the HomeLink® transmitter does not activate the operator or distance is inadequate,verify proper operation using the hand-held transmitter. Contact your HomeLink® system provider for help with configuring the HomeLink® transmitter and to resolve distance problems when using the HomeLink® system.

Classic Quik-Code Transmitter

Installation Instructions

Replacement for Models:

•9921T	•9931T	•8822T	•8832T
•8833T	•9921MT	•9931MT	•9921TK
•9931TK	•8832TK	•9931TK6

Product Features
The Classic Quik Code Transmitter makes it	Programming the Classic is done by simply:
possible to operate a single or group of remotely	1.	Put the transmitter in program mode.
controlled devices such as a garage door opener,	2.	Select the button you wish to use.
with a single transmitter.	3.	Enter your 9 digit code.

Follow these simple instructions.

Please read the instructions completely before starting.

Further instructions are available at www.allstarcorp.com

INSTRUCTIONS FOR REPLACEMENT TRANSMITTERS

Manufacturer’s Limited Warranty

Allstar warrants its radio controls to be free from defect in material and workmanship for a period of one (1) year from the date of purchase. To obtain service, contact your dealer.

To obtain service under this warranty the buyer must obtain authorization instructions for the return of any goods from Allstar before returning the goods. The goods must be returned with complete identification, with copy of proof-of-purchase, freight prepaid and in accordance with Allstar’s instructions or they will not be accepted. In no event will Allstar be responsible for goods returned without proper authorization or identification.

Goods returned to Allstar for warranty repair within the warranty period, which upon receipt by Allstar are confirmed to be defective and covered by this limited warranty, will be repaired or replaced at Allstar’s sole option, at no cost and returned pre-paid. Defective parts will be repaired or replaced with new or factory rebuilt parts at Allstar’s sole option.

This limited warranty does not cover non-defect damage, damage caused by unreasonable use, damage caused by improper installation or care, vandalism or lightning, fire or excessive heat, flood or other acts of God (including, but not limited to misuse, abuse or alterations, failure to provide reasonable and necessary maintenance), labor charges for dismantling or reinstalling a repaired or replaced unit, or replacement batteries.

These warranties are in lieu of all other warranties, either expressed or implied. All implied warranties of merchantability and/or fitness for a particular purpose are hereby disclaimed and excluded. Under no circumstances shall Allstar be liable for consequential, incidental or special damages arising in connection with the use or inability to use this product. In no event shall Allstar’s liability for breach of warranty, breach of contract, negligence or strict liability exceed the cost of the product covered hereby. No person is authorized to assume for Allstar any other liability in connection with the sale of this product.

This warranty gives you specific legal rights. Warranty effective after July 24, 2002.

WARNING

Unexpected door operations can cause personal injury or property damage.

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Select the block of switches below that best matches the one in the

transmitter or receiver that you are replacing.

*The grids display an EXAMPLE using the code shown on the switches to the left.

9 switches w/ + 0 -
	1	2	3	4	5	6	7	8	9
	-	-	0	0	+	+	-	0	+
						turn page Go to Step 1...
9 switches w/ On & Off
	1	2	3	4	5	6	7	8	9
	-	-	+	+	-	-	+	+	-	turn page
OR										Go to
										Step 1a
	1	2	3	4	5	6	7	8	9
	-	-	+	+	-	-	+	+	-
8 switches w/ + 0 -
	1	2	3	4	5	6	7	8	9
	-	-	0	0	+	+	-	0	+
						turn page Go to Step 1...

WARNING

Disconnect power to operator before any installation or repair. Follow all

instructions provided by the manufacturer of your operator.

Copyright © 2002 c.p.Allstar Corporation PART NUMBER 111243 REV F	Allstar Radio Controls are compatible with HomeLink®.
	Homelink® is a registered trade mark of Johnson Controls, Inc.