48-EN
Mixing bass sound to the rear channel
(REAR MIX)
This function mixes the front channel audio signals to the audio
signals output from the rear speakers, improving the sound in the
vehicle’s rear seat.
•Avoid stopping, pausing, switching the disc, cueing, fast-
forwarding or switching the audio channel of this unit while
making this adjustment. The setting is cancelled if the Decode
mode is switched.
1Check that Defeat mode is off (page 20).
2Press and hold MENU for at least 2 seconds.
3Select the Multi CH Setup mode by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Multi CH
Setup mode.
4Select the REAR MIX mode by sliding your finger
on the GlideTouch bar to the left or right. Press
the GlideTouch bar under the REAR MIX mode.
5Select the REAR MIX ON/OFF by sliding your finger
on the GlideTouch bar to the left or right. Press
the GlideTouch bar under the REAR MIX ON/OFF.
If ON is set, the audio signal which is output from the rear
speaker is mixed to the front audio signal.
6Adjust the level by turning and then pressing the
Rotary encoder.
The level can adjusted in five steps: –6, –3, 0, +3 and +6. The
higher the level, the more bass is output from the rear
speakers. (The effect differs according to the software (DVD,
etc.).)
7When the setting is complete, press and hold
MENU for at least 2 seconds.
•This adjustment is ineffective when the rear speaker setup setting is
set to “OFF.”
•For linear PCM signals, the voice is output from the rear speaker
regardless of the REAR FILL and REAR MIX setting.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 51.
6When the setting is complete, press and hold
MENU for at least 2 seconds.
• The subwoofer can be set only to ON/OFF.
•If the centre speaker is turned “OFF,” the centre channel’s audio
signals are added to the audio signals output from the front
speakers.
•If you set the speaker response to “OFF,” also set the speaker
setting to “OFF.” (page 44)
•Perform the setup for all the speakers (“Front,” “Center,” “Rear”
and “Subwoofer”). If not, the sound may not be balanced.
• When centre is set to “OFF”, the setting is ineffective even if
centre is set with this function.
•Through changing the settings on each speaker, a change in the
output of the other speakers may occur due to the setting
requirements.
•When using the PRO LOGIC II, if the rear speaker is set to
“LARGE”, then there will be no output from the subwoofer.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 51.

Setting of Dolby Digital

Adjusting the speaker levels (OUTPUT LEVEL)
The test tones help to make the volume adjustments of the different
speakers. When levels are equal, a strong sense of presence can be
heard from the different speakers at the listening position.
•Avoid stopping, pausing, switching the disc, cueing, fast-
forwarding or switching the audio channel of this unit while
making this adjustment. The setting is cancelled if the decode mode
is switched.
1Check that Defeat mode is off (page 20).
2Press and hold MENU for at least 2 seconds.
3Select the Multi CH Setup mode by sliding you
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Multi CH
Setupmode.
4Select OUTPUT LEVEL by sliding your finger on
the GlideTouch bar to the left or right. Press the
GlideTouch bar under the OUTPUT LEVEL mode.
The test tone is reproduced by each speaker automatically.
5Adjust the output level by turning the Rotary
encoder to balance the volume of each speaker.
•The adjustment range for the different speakers is –10 dB - +10 dB.
•Adjust based on the front speakers.
6When the setting is complete, press and hold
MENU for at least 2 seconds.
•If a speaker is set to off mode, that speaker’s level adjustment
cannot be made. Refer to “Speaker Setup” (page 47).
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 51.
•While adjusting the speaker, it cannot be switched.