SATA-II 2 Primary RAID, On-Chip IDE Channel0 | AMD GA-K8N51GMF-9

SATA-II 2 Primary RAID

Enabled	Enable SATAII 2 1st SATA RAID function.
Disabled	Disable this function. (Default value)

SATA-II 2 Secondary RAID

Enabled	Enable SATAII 2 2nd SATA RAID function.
Disabled	Disable this function. (Default value)

On-Chip IDE Channel0

Enabled	Enable onboard 1st channel IDE port. (Default value)
Disabled	Disable onboard 1st channel IDE port.

On-Chip IDE Channel1

Enabled	Enable onboard 2nd channel IDE port. (Default value)
Disabled	Disable onboard 2nd channel IDE port.

IDE1 Conductor Cable

Auto BIOS autodetects IDE1 conductor cable. (Default Value)

ATA66/100/133 Set IDE1 Conductor Cable to ATA66/100/133 (Please make sure your IDE

	device and cable are compatible with ATA66/100/133).
ATA33	Set IDE1 Conductor Cable to ATA33. (Please make sure your IDE device
	and cable are compatible with ATA33)

IDE2 Conductor Cable

Auto BIOS autodetects IDE2 conductor cable. (Default Value)

ATA66/100/133 Set IDE2 Conductor Cable to ATA66/100/133. (Please make sure your IDE

	device and cable are compatible with ATA66/100/133)
ATA33	Set IDE2 Conductor Cable to ATA33. (Please make sure your IDE device
	and cable are compatible with ATA33)

Serial-ATA-II 1

Enabled	Enable Serial-ATAII 1 support. (Default Value)
Disabled	Disable Serial-ATAII 1 support.

Serial-ATA-II 2

Enabled	Enable Serial-ATAII 2 support. (Default Value)
Disabled	Disable Serial-ATAII 2 support.

On-Chip USB

V1.1+V2.0	Enable USB 1.1 and USB 2.0 controllers. (Default Value)
V1.1	Enable only USB 1.1 controller
Disabled	Disable onchip USB support.

USB Keyboard Support

Enabled	Enable USB keyboard support.
Disabled	Disable USB keyboard support. (Default value)

USB Mouse Support

Enabled	Enable USB mouse support.
Disabled	Disable USB mouse support. (Default value)

Onboard Audio Function

Auto	Auto-detect onboard audio function. (Default value)
Disabled	Disable this function.

	- 37 -	BIOS Setup

English

Image 37

AMD GA-K8N51GMF-9 user manual SATA-II 2 Primary RAID, SATA-II 2 Secondary RAID, On-Chip IDE Channel0, On-Chip IDE Channel1

Contents

GA-K8N51GMF-9 Motherboard Product Manual Classification Copyright Table of Contents Drivers Installation K8N51GMF-GA GA-K8N51GMF-9 Motherboard Layout Block Diagram Page Installation Notices Considerations Prior to InstallationInstances of Non-Warranty Preparing Your Computer ALC880 Codec Feature Summary Use of licensed Award Bios Installation of the CPU Installation of the CPU and Fan Heat Sink Installation of the Fan Heat Sink Installation of Memory Dual Channel Memory Configuration Installation of Expansion Cards I/O Back Panel Introduction Center/Subwoofer Speaker Out Connectors IntroductionSide Speaker Out ATX12V/ATX Power Connector FDD FDD Connector Cpufan / Sysfan Cooler Fan Power Connector SATAII0/1/2/3 Sata 3Gb/s Connectors, Controlled by nForce IDE1 / IDE2 IDE Connector Faudio Front Audio Connector Fpanel Front Panel Jumper Pwrled Cdin CD In Connector 13 F11394 Ieee 1394 Connector USB1 / FUSB2 Front USB Connector Spdifio Spdif In/Out Coma Coma Connector CI Chassis Intrusion, Case Open Clrcmos Clear Cmos Battery Main Menu Status Page Setup Menu / Option Page Setup Menu Main Menu For example Bios Ver. F1g „ Set User Password „ Set Supervisor Password„ Save & Exit Setup „ Exit Without Saving Time Standard Cmos FeaturesIDE Channel 0 Master/Slave IDE Channel 1 Master/Slave Drive a Floppy 3 Mode Support for Japan AreaHalt on Memory Hard Disk Boot Priority Advanced Bios FeaturesFirst / Second / Third Boot Device Boot Up Floppy Seek Init Display First Password Check SPP Integrated Peripherals SATA-II 2 Secondary RAID SATA-II 2 Primary RAIDOn-Chip IDE Channel0 On-Chip IDE Channel1 Parallel Port Mode Onboard LAN Boot ROMOnboard LAN Function Onboard 1394 Function Power-On by Alarm Power Management SetupPME Event Wake Up Modem Ring On KB Power on Password Power On By KeyboardPower On By Mouse AC Back Function PCI 1 IRQ Assignment PnP/PCI Configurations PC Health Status CPU Frequency Frequency/Voltage ControlPcie Clock K8 CPU Clock Ratio Load Optimized Defaults Load Fail-Safe Defaults Set Supervisor/User Password Exit Without Saving Save & Exit Setup Install Chipset Drivers Drivers Installation Software Information Software Application Contact Us Hardware Information English EasyTune 5 Introduction Unique Software UtilitiesUser Interface Overview What is Xpress Recovery ? Xpress Recovery IntroductionHow to use the Xpress Recovery Press F9 during powering on the computer. Text Mode F9 For Xpress Recovery Exit and Restart Remove Backup Image Remove backup image. Are you sure? Y/N Method 1 Q-FlashTMUtility Flash Bios Method IntroductionBefore You Begin Task menu for Dual Bios utility Exploring the Q-FlashTM / Dual Bios utility screenEntering the Q-FlashTMutility Task menu for Q-Flash utility Steps Using the Q-FlashTMutility You can repeat to Part Two Task menu for Q-FlashTMutility FlashTMutility bar Exploring the Q-FlashTMutility screen Bios file becomes F4 after updating Congratulation!! You have updated Bios successfully Methods and steps Method 2 @BIOSTM Utility English RAID Levels Serial ATA Bios Setting Utility Introduction Entering the RAID Bios Setup Configuring the Nvidia RAID Bios Selecting the RAID Mode Using the Define a New Array WindowSelecting the Striping Block Size Assigning the Disks Completing the RAID Bios Setup Array 2 Nvidia Mirror 111.79G Cd bootdrv Menu Installing the RAID drivers 5 2- / 4- / 6- / 8- Channel Audio Function Introduction Stereo Speakers Connection and Settings Channel Audio Setup English English Sound Effect Configuration AMI Bios Beep Codes Troubleshooting English Appendix English Taiwan Headquarters Contact Us China Shanghai