American Standard 0427.444 dimensions Cadet Round Countertop Sink, Nominal Dimensions, Bowl sizes

BARRIER FREE

CADET™ ROUND COUNTERTOP SINK

VITREOUS CHINA

CADET™ ROUND COUNTERTOP SINK

•European-styled interior bowl

•Available with Scotchgard® finish for easier cleaning

•Made from vitreous china

•Self-rimming with cutout template supplied

•Front overflow

❏0427.444 Faucet holes on 4" (102mm) centers (illustrated)

❏0427.888 Faucet holes on 8" (203mm) centers

❏0427.111 Center hole only

❏0427.444SG Faucet holes on 4" (102mm) centers (with Scotchgard® finish)

❏0427.888SG Faucet holes on 8" (203mm) centers

(with Scotchgard® finish) Available with

Nominal Dimensions:

19" dia. (483mm) Round

Bowl sizes:

15-1/4" (387mm) wide

12-1/4" (311mm) front to back 6" (152mm) deep

Compliance Certifications - Meets or Exceeds the Following Specifications:

•ASME A112.19.2M for Vitreous China Fixtures

•CAN/CSA B45 series

To Be Specified:

❏Color: ❏ White ❏ Bone

❏Linen ❏ Silver

❏ Fawn Beige ❏ Black

❏ Faucet*:

FINISHED WALL OR SPLASHBACK

SEALING COMPOUND

COUNTERTOP (BY OTHERS)

*10-3/4" (273mm)

*12-7/8" (327mm)

				24
			4	(610mm)
4"	3-1/8"	OPTIONAL	(102mm)
(102mm)	(79mm)
		7-1/2"
		(191mm)
				8	DRAWING FOR
				(203mm)
		19"			DIMENSIONAL
		(448mm)		MIN.	PURPOSES ONLY.
				IT IS NOT AN EXACT
		33-1/4		REPRESENTATION.
		(845mm)
			27
			(686mm)
			MIN.		6
	19"	3/4"			(152mm)
					MAX.
		(19mm)
	(483mm)
				BARRIER FREE
				CLEARANCE	9
					(229mm)
		8"			MIN.
		(203mm)
	SUPPLIES	31"
	AS REQ'D	(787mm)
	8"	SUGGESTED
	(203mm)	33-1/4"
	1-1/4" O.D. WASTE
		(845mm)
	1-1/4" O.D. TAILPIECE

❏ Faucet Finish:

❏ Supplies:

❏ 1-1/4" Trap:

FINISHED FLOOR

* See faucet section for additional models available

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDELINES AND ANSI A117.1 ACCESSIBLE AND USABLE

BUILDINGS AND FACILITIES - CHECK LOCAL CODES.

Install lavatory 864mm (34") from finished floor. Lavatory installed 51mm (2") minimum from front edge of countertop provides 686mm (27") knee clearance area.

NOTES:

*DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE SUGGESTED.

FOR COUNTERTOP CUTOUT AND INSTALLATION INSTRUCTIONS USE TEMPLATE SUPPLIED WITH SINK.

FITTINGS NOT INCLUDED WITH FIXTURE AND MUST BE ORDERED SEPARATELY.

SEALING COMPOUND SUPPLIED BY OTHERS.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard A112.19.2. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.

	J40
© 2008 AS America Inc.		Revised 2/08