Manuals / American Standard / Household Appliance / Indoor Furnishings

American Standard 2385.W Front, Connect Supplies, Install Pop-Updrain, Test Installed Faucet

Models: 2385.R 2385.W

1 2
Download 2 pages 14.84 Kb
Page 2
Image 2
2 CONNECT SUPPLIES

2 CONNECT SUPPLIES

Carefully bend copper supplies to meet water supply lines using the palms of the hands to avoid kinking.

Connect HOT water supply line to LEFT tube, and COLD water supply line to RIGHT tube using appropriate connectors.

OR

3 INSTALL POP-UP DRAIN

FLANGE

Push DRAIN BODY down into trap.

 

Thread LOCKNUT, WASHER and GASKET onto

SINK

DRAIN BODY.

 

STOPPER

FLANGE

GASKET

Remove one end of CLIP from PIVOT ROD by squeezing ends together while sliding.

Insert PIVOT ROD into second or third hole in EXTENSION and reassemble CLIP. (EXTENSION may need to be bent.)

Adjust STOPPER height by repositioning EXTENSION and tightening THUMBSCREW.

Feed DRAIN BODY up through SINK. Place FLANGE GASKET over BODY and thread FLANGE FULLY onto BODY.

Tighten LOCKNUT firmly, keeping the PIVOT ROD pointed towards the back of the SINK.

Drop STOPPER into DRAIN BODY.

LOCKNUT

 

Position EXTENSION ROD onto POP-UP ROD and tighten THUMBSCREW.

DRAIN 3 INSTALL POP-UP DRAIN

BODY

GASKET

WASHER

CLIP

PIVOT

ROD

TRAP

THUMBSCREW

EXTENSION

ROD

DRAIN 4 TEST INSTALLED FAUCET BODY 5 HOT LIMIT STOPFRONT

TRAP

POP-UP ROD

EXTENSION

ROD

CLIP

PIVOT

ROD

4 TEST INSTALLED FAUCET

Move handle down into "off" position and remove AERATOR.

For vandal-resistant FLOW DEVICE, insert KEY teeth into slots near outlet and turn.

Turn on water supplies and check connections for leaks.

Operate handle up and down, left and right to flush water lines thoroughly.

Move handle down to "off" position and replace AERATOR or FLOW DEVICE.

5 HOT LIMIT STOP

By restricting handle rotation and limiting the amount of hot water allowed to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental scalding. To set the maximum hot water temperature of your RELIANT faucets, all you need to do is adjust the setting on the HOT LIMIT SAFETY STOP.

Remove HANDLE, CAP and HOT LIMIT STOP. Follow "A" or "B" to adjust maximum discharge temperature.

"A"

PRY UPWARD TO UNLOCK

AND ROTATE COUNTER- CLOCKWISE ONE CLICK

FRONT

ADJUSTMENT WHEN WATER IS TOO HOT

"B"

PRY UPWARD TO UNLOCK AND ROTATE CLOCKWISE

FRONT

ADJUSTMENT WHEN

WATER IS TOO COLD

6 SERVICE

AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR. Clean AERATOR and FLOW RESTRICTOR. Replace AERATOR.

If faucet drips, operate handle several times from "off" to "on". Do not apply excessive force.

Clogged CARTRIDGE inlets may cause reduced flow in "full on" hot or cold. To clean inlets, first turn off water supply, then:

Remove HANDLE, CAP, HOT LIMIT STOP and CARTRIDGE. Clean inlets and MANIFOLD.

Reassemble CARTRIDGE, alternately tightening screws. Replace HOT LIMIT STOP , CAP and HANDLE. Check flow.

HANDLE

CARTRIDGE

SET SCREW

SEALS

 

HANDLE

 

BUSHING

 

CAP

P0P-UP

 

HOT LIMIT

ROD

 

STOP

 

CARTRIDGE

 

SCREWS

 

CAP

 

RETAINER

AERATOR

 

 

HOTLINE FOR HELP

 

For toll-free information and answers to your questions, call:

 

1 (800) 223-0068

 

Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

C A m e r i c a n S t a n d a r d I n c . 1 9 9 3

 

7 8 5 2 3 C

Page 1
Page 2
Image 2
American Standard 2385.W Front, Connect Supplies, Install Pop-Updrain, Test Installed Faucet, Hot Limit Stop, Service
Page 1

FAQ

How do I connect supplies for American Standard indoor furnishings?

Carefully bend copper supplies to meet water supply lines using the palms of the hands to avoid kinking. Connect the HOT water supply line to the LEFT tube and the COLD water supply line to the RIGHT tube using appropriate connectors.

How do I test the installed faucet?

Move the handle down into the 'off' position and remove the aerator. For vandal-resistant flow devices, insert the key teeth into slots near the outlet and turn. Turn on water supplies and check connections for leaks. Operate the handle up and down, left and right to flush water lines thoroughly. Move the handle down to the 'off' position and replace the aerator or flow device.

How can I service the indoor furnishings?

If the faucet drips, operate the handle several times from 'off' to 'on'. Do not apply excessive force. Clogged cartridge inlets may cause reduced flow in 'full-on' hot or cold. To clean inlets, first turn off water supply, then remove the handle, cap, hot limit stop, and cartridge. Clean inlets and manifold. Reassemble the cartridge, alternately tightening screws. Replace the hot limit stop, cap, and handle. Check flow.