American Standard 2425.118WC, 2425.218WC dimensions General Specifications for 2425 Whirlpool

HAMPTON™ 5’ INTEGRAL APRON

WHIRLPOOL

HIGH GLOSS ACRYLIC

		60
	12	(1524mm)
			WATER
10-1/4	(305mm)
			RETENTION
(260mm)			FLANGE
3/4
		(8) JETS	(3 SIDES)
(19mm)
FINISHED
SEE FITTING WALL
SPECS FOR				16
DIMENSIONS
				(406mm)
		9
		(229 mm)
32			PUMP	ON/OFF
				SWITCH
(813mm)		CUTOUT IN FLOOR FOR DRAIN
C/L OF	3	(2) AIR VALVES		ACCESS TO PUMP/MOTOR
SUPPLIES	(76mm)			THROUGH REMOVABLE
				FRONT ACCESS PANEL

	C/L OF DRAIN			C/L OF
				SHOWER ARM
				FINISHED
OPTIONAL TO		SAFE-T-HEATER			WALL
FINISHED FLOOR
	1" WATER	REMOVABLE			C/L OF
USUALLY BETWEEN
		BLANK
65 & 78	RETENTION				VALVES
(1651 & 1981mm)	FLANGE
	(3 SIDES)				C/L OF
		12
	C/L OF
		(305mm)			SPOUT
	OVERFLOW
		OPT.	4
	3-1/2				TILING	LEVELING STRINGER
	(89mm)		(102 mm)		FLANGE	NOT FOR SUPPORT

TOP OF				UNDERSIDE
DECK	21-1/2		21-1/4	OF DECK
	(546mm)		(540mm)
			REF.
	ROUGH		DIM
	FLOOR
	BATH	1-1/2 N.P.T.M.
	SUPPORT	THREADS	2-3/4
	MATERIAL	1-1/2 O.D.TAILPIECE	(70mm)
			4-5/8
			(117mm)

GENERAL SPECIFICATIONS FOR 2425 WHIRLPOOL

INSTALLED SIZE	60 X 32 X 21-1/2In.(1524 X 813 X 546mm)
WEIGHT						115 Lbs. (52 Kg.)
WEIGHT w/WATER					574 Lbs. (258 Kg.)
GAL. TO OVERFLOW							55 Gal. (208 L.)
MIN. OPERATING GAL.							45 Gal. (171 L.)
BATHING WELL AT SUMP			16-1/4 X 38-1/4 In. (413 X 972mm)
BATHING WELL AT RIM		26-1/4 X 52-1/2 In. (667 X 1334mm)
WATER DEPTH TO OVERFLOW								15 In. (381mm)
FLOOR LOADING				43 Lbs./Sq. Ft. (208 Kgs/Sq. m.)
(PROJECTED AREA)
PTS.									15.6
CUBE (FT3)									35.3

WHIRLPOOL ELECTRICAL SPECIFICATIONS

SYSTEM I PUMP 1.6 HP, 9.7 AMPS, 120V.

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE

INSTALLATION. SUPPORT OF BATH BY SUMP BEDDING. SUPPORT AND ENCLOSING MATERIAL BY OTHERS.

REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

IMPORTANT:

Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

© 2003 American Standard Inc.