American Standard 2425.XXXW SERIES installation instructions General Installation Information

HAMPTON 5' x 32"™

DROP-IN

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2425.XXXW SERIES WHIRLPOOL

INSTALLATION INSTRUCTIONS

				60
		12		(1524mm)
10-1/4		(305mm)				ON/OFF
(260mm)						SWITCH
	3/4
	(19mm)
	FINISHED
SEE FITTING WALL
SPECS FOR
DIMENSIONS
		9
		(229 mm)
						PROVIDE ACCESS
32					PUMP	TO PUMP FOR
						SERVICE ON ALL
	16
(813mm)		CUTOUT IN FLOOR FOR DRAIN				INSTALLATIONS
	(406mm)
C/L OF		3			(8) JETS	OUTLINE OF CUTOUT
SUPPLIES		(76mm)		(2) AIR VALVES
						58-1/2 X 30-1/2
		C/L OF DRAIN			C/L OF	(1486 X 775mm)
					SHOWER ARM
					FINISHED
OPTIONAL TO					WALL
FINISHED FLOOR		■ LEVELING			C/L OF
USUALLY BETWEEN
		STRINGER
	65 & 78				VALVES
		NOT FOR
(1651 & 1981mm)
		SUPPORT
		C/L OF		12	C/L OF
		OVERFLOW	(305mm) OPT.		SPOUT
		3-1/2		4	2
		(89mm)		(102mm)	(51mm)
						UNDERSIDE
		21-1/2			19-1/2	OF DECK
		(546mm)			(495mm)
		ROUGH				SAFE-T-HEATER
						REMOVABLE
		FLOOR
						BLANK
		INTEGRAL		1-1/2 N.P.T.M.
				THREADS	2-3/4
		FEET
					(70mm)
		1-1/2 O.D.TAILPIECE
					4-5/8
					(117mm)
	GENERAL SPECIFICATIONS FOR 2425 WHIRLPOOL
	INSTALLED SIZE			60 x 32 x 21-1/2 (1524 x 813 x 546mm)
	WEIGHT				115 Lbs. (52 Kg.)
	WEIGHT w/WATER				574 Lbs. (258 Kg.)
	GAL. TO OVERFLOW				55 Gal. (208 L.)
	WHIRLPOOL MIN. OPERATING VOL.				45 Gal. (171 L.)
	BATHING WELL AT SUMP			16-1/4 x 38-1/4 (413 x 972mm)
	BATHING WELL AT RIM			26-1/4 x 52-1/2 (667 x 1334mm)
	WATER DEPTH TO OVERFLOW				15 (381mm)
	FLOOR LOADING			43 Lbs./Sq.Ft. (208 Kgs./Sq.m)
	(PROJECTED AREA)
	PTS.				15.6
	CUBE (FT3)				35.3
		WHIRLPOOL ELECTRICAL SPECIFICATIONS
	PUMP			1.6 HP, 9.7 AMPS,120V.

GENERAL INSTALLATION INFORMATION

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Optional Components (not included):

•Tile Bead Kit 751755-100*

•Safe-T-Heater 9075.120*

List of Required Components (not included):

• Drain 1583.470* • Bath Filler*

* see your American Standard Distributor

List of Required Tools and Supplies:

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	15 amp GFI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2003

753457-100 REV. BAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.