American Standard 2425E-RHO installation instructions General Installation Information, enclosure

WILLIAMSBURG ELITE™ 5'

INTEGRAL APRON WITH REMOVABLE ACCESS PANEL HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2425E-LHO

2425E-RHO WHIRLPOOL

INSTALLATION INSTRUCTIONS

			60
	12	(1524mm)
10-1/4	(305mm)			WATER
				RETENTION
(260mm)				FLANGE
3/4
			(8) JETS	(3 SIDES)
(19mm)
FINISHED
SEE FITTING WALL
SPECS FOR						16
DIMENSIONS
						(406mm)
	9
	(229 mm)
32				PUMP		ON/OFF
						SWITCH
(813mm)	CUTOUT IN FLOOR FOR DRAIN
C/L OF	3		(2) AIR VALVES		ACCESS TO PUMP/MOTOR
SUPPLIES	(76mm)				THROUGH REMOVABLE
					FRONT ACCESS PANEL
	C/L OF DRAIN			C/L OF
				SHOWER ARM
				FINISHED
OPTIONAL TO		IN-LINE HEATER		WALL
FINISHED FLOOR
USUALLY BETWEEN	1" WATER	REMOVABLE		C/L OF
65 & 78	RETENTION	BLANK		VALVES
(1651 & 1981mm)	FLANGE
	(3 SIDES)	12		C/L OF
	C/L OF
		(305mm)		SPOUT
	OVERFLOW	OPT.	4		TILING
	3-1/2					LEVELING STRINGER
			(102 mm)		FLANGE	NOT FOR SUPPORT
	(89mm)

TOP OF				UNDERSIDE
DECK	21-1/2		21-1/4	OF DECK
	(546mm)		(540mm)
			REF.
	ROUGH		DIM
	FLOOR
	BATH	1-1/2 N.P.T.M.
	SUPPORT	THREADS	2-3/4
	MATERIAL	1-1/2 O.D.TAILPIECE	(70mm)
			4-5/8
			(117mm)

Left-hand version shown

GENERAL SPECIFICATIONS FOR 2425E WHIRLPOOL

INSTALLED SIZE		60 x 32 x 21-1/2 (1524 x 813 x 546mm)
WEIGHT							115 Lbs. (52 Kg.)
WEIGHT w/WATER						574 Lbs. (258 Kg.)
GAL. TO OVERFLOW								55 Gal. (208 L.)
WHIRLPOOL MIN. OPERATING VOL.								45 Gal. (171 L.)
BATHING WELL AT SUMP				16-1/4 x 38-1/4 (413 x 972mm)
BATHING WELL AT RIM			26-1/4 x 52-1/2 (667 x 1334mm)
WATER DEPTH TO OVERFLOW									15 (381mm)
FLOOR LOADING				43 Lbs./Sq.Ft. (208 Kgs./Sq.m)
(PROJECTED AREA)
PTS.										20.8
CUBE (FT3)											35.3
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP					1.6 HP, 9.7 AMPS,120V.

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. the whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool. To insure maximum performance and pleasure from this

product, please follow the instructions and cautions.

List of Optional Components (not included):

•Flex-Jet Pulse Jet Kit*

•Flex-Jet Soft Jet Kit*

•E-Z-Install Heater*

List of Required Components (not included):

•	Drain*	• Bath Filler*
* see your Home Depot Retailer
List of Required Tools and Supplies:
Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	15 amp GFI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

General Installation Information

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately. After inspection and during installation, protect the bath from construction damage. Before installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks. Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system. Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others.

General Installation Information	IMPORTANT: Water test unit before installation and
	enclosure!
Bath may only be installed in a recess type installation.

Locate studs as required. insure rough dimensions are proper, plumb and square. For whirlpools, access to pump/motor may be made through access opening in apron panel. The following procedure must be used for all installations: leveling support stringer should be as indicated. this bath is not self-supporting and must be supported along it's entire bottom. Support with mortar or grout. Position bathtub/whirlpool within the recess, check level, front to back, side to side, and shim as necessary. To secure the tub to wood studs use drywall screws w/washers or roofing nails immediately above the flange of the tub.To secure the tub to steel studs use 4" drywall screws and flatwashers.

See page 2 for complete installation information.

Caution: Take extra care when driving nails or screws to avoid damaging the tub. The tile or similar finished floor will be butted against the bottom of the tub apron, also holding the tub in place.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2002

752876-100 Rev. EAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.