INSTALLATION
INSTRUCTIONS
BATH FILLER SUPPLIES
MODEL 9117.012
To ensure this product is installed properly, please read these instructions carefully before you begin.
DESCRIPTION
Bath Filler Supplies, Model 9117.012, includes 6” deck mount supply adapters, riser tubes, couplings, shutoff valves, and all fittings and supports needed to install and connect the 9116 Series Bath Filler to the water supplies.
Adjust centerline spacing of supports and water supply lines as needed to accommodate American Standard 9116 Series Bath Filler. Please refer to Bath Filler Installation Instructions for this dimension.
RECOMMENDED TOOLS AND MATERIALS
Hacksaw/Tubing Cutter | Drill, misc. bits | Pipe | Teflon Tape (pipe sealant) or |
Phillips Screwdriver | 1" Hole Saw or Spade Bit | Wrench | Teflon Based Pipe Sealant |
Level | Clear Silicone Sealant | ||
Tape Measure | Wrench Torpedo | Plumb Bob |
|
DO NOT USE PIPE DOPE FOR THREADED CONNECTIONS AS FINISH DETERIORATION MAY RESULT. INSTALLATION MUST COMPLY WITH APPLICABLE LOCAL PLUMBING/BUILDING CODES
|
|
|
|
|
|
|
|
| FLANGE | ||||
|
|
|
|
|
|
|
|
|
| NUT | |||
5" DECK MOUNT | GASKET | SUPPLY |
|
| WASHER |
|
| FLANGE | |||||
ADAPTER |
|
|
| FLOOR |
|
|
| ||||||
| UNION | RISER |
|
|
| SCREWS | |||||||
|
|
| ESCUTCHEON |
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| |||
|
|
| NIPPLE |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| VALVE |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| ||||||
|
|
|
| HANDLE |
|
| |||||||
|
|
|
|
|
|
|
|
|
| SCREW | FLOOR | ||
|
|
|
|
|
|
|
|
|
| FLANGE | |||
|
|
|
|
|
|
|
|
|
|
| |||
DECK MOUNT | FLANGE |
| COVER |
|
|
|
|
|
|
| |||
WASHER | NUT |
|
|
|
|
| |||||||
UNION | Assembly | ||||||||||||
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
Step 1. Locate and mark correct centerline dimension for Bath Filler on bath deck per
Step 2. Extend hole centerlines from bath to floor using Plumb Bob.
Step 3. Drill 1" diameter holes for supply risers at locations marked in step 2.
NOTE: Water supplies are primarily factory assembled and water tested. DO NOT attempt to disassemble supplies, as surface may be damaged and warranty will be void.
Step 4. Assemble floor escutcheons and base flange to short pipe on supply risers. Insert supply risers into floor mounting holes (with shutoff valves facing outward) and loosely install flat washers and locknuts on pipe nipples from beneath floor.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . © A m e r i c a n S t a n d a r d I n c . 2 0 0 4
752870 - 100 Rev . A