American Standard 2805.XXXW installation instructions Series Whirlpool Installation Instructions

HERITAGE 5' x 42"™

HIGH GLOSS ACRYLIC SHOWN LESS ALL FITTINGS

2805.XXXW

SERIES WHIRLPOOL

INSTALLATION INSTRUCTIONS

	1524mm
	(60)
762mm	INTEGRAL
	FITTING DECK	152mm
(30)
		(6)
305mm		C/L OF
(12)
		DRAIN
		PUMP
1067mm	178mm x 381mm
	(7 x 15)
(42)
	FLOOR
		PROVIDE ACCESS
	CUTOUT
		TO PUMP FOR
		SERVICE ON ALL
		INSTALLATIONS
		ON/OFF
		SWITCH
		19mm
		(3/4)
	OUTLINE OF CUTOUT
	1486mm x 1029mm
	(58-1/2 x 40-1/2)

THANK YOU...

for selecting an American Standard bath. Your new bath is shipped to you after careful inspection. The whirlpool version is completely assembled with pump, motor, and system piping. All you need to finish the installation are your selected fittings and electrical connections for a whirlpool.

To insure maximum performance and pleasure from this product, please follow the instructions and cautions.

List of Optional Components (not included):

• 5 Foot Apron*

• Safe-T-Heater 9075.120*

SAFE-T-HEATER

51mm(2) REMOVABLE BLANK

546mm (21-1/2)

495mm (19-1/2)

ROUGH

FLOOR

INTEGRAL

FEET

SUPPORT

LEVELING STRINGER

NOT FOR SUPPORT

133mm (5-1/4)

C/L OF

OVERFLOW

64mm (2-1/2)

1-1/2 N.P.T.

THREADS

1-1/2 O.D.

TAILPIECE121mm (4-3/4)

*see your American Standard Distributor

List of Required Components (not included):

•Drain 1583.470*

•Bath Filler*

* see your American Standard Distributor

List of Required Tools and Supplies:

GENERAL SPECIFICATIONS FOR 2805 WHIRLPOOL

INSTALLED SIZE		60 x 42 x 21-1/2 In. (1524 x 1067 x 546mm)
WEIGHT				130 Lbs. (59 Kg.)
WEIGHT w/WATER				689 Lbs. (310 Kg.)
GAL. TO OVERFLOW				64 Gal. (243 L)
WHIRLPOOL MIN. OPERATING VOL.				52 Gal. (197 L)
BATHING WELL AT SUMP				43 x 22 In. (1092 x 559mm)
BATHING WELL AT RIM			55 x 35-1/2 In. (1397 x 902mm)
WATER DEPTH TO OVERFLOW				15 In. (381mm)
FLOOR LOADING			39 Lbs./Sq.Ft. (191 Kgs./Sq.m)
(PROJECTED AREA)
PTS.					27.8
CUBE (FT3)						47.4
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP				1.6 HP, 9.7 AMPS ,120V.
SYSTEM II PUMP				2.1 HP, 15.6 AMPS ,120V.

GENERAL INSTALLATION INFORMATION

Tools		Supplies
•	Level	•	Nails
•	Tape Measure	•	Putty
•	Pipe Wrench	•	Caulking (waterproof)
•	Slip Joint Pliers	•	1 x 3 or 2 x 2
•	Screw Driver		Stringers
•	Standard	•	Drop Cloth
	Woodworking Tools	•	15 or 20 amp GFCI
•	Personal Safety		Outlet
	Equipment	•	Cement, Plaster,
•	Caulking Gun		Grout

Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor immediately.

After inspection and during installation, protect the bath from construction damage. After installation, and before enclosing with wallboard, tile, etc., water test the unit and check for leaks.

Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump, motor, or piping system.

Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead (required for recess installations).

Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.

WARNING! Do not lift whirlpool by the piping harness at any time.

FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.

© American Standard Inc. 2004

752294-100 Rev. KAll product names listed herein are trademarks of American Standard Inc. unless otherwise noted.