American Standard 2823 installation instructions Tissue Holder, Series, Série

Installation Instructions
Instrucciones de instalación
Mode d’installation
TISSUE HOLDER	2823 SERIES
SOPORTE PARA PAPEL HIGIÉNICO	SERIE 2823
SUPPORT DE PAPIER TOILETTE	SÉRIE 2823

Thank you for selecting American-Standard...the benchmark of fine

quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin.

Gracias por seleccionar los productos American Standard, sinónimo de la mejor calidad durante más de 100 años. Por favor lea estas instrucciones detenidamente antes de comenzar para que lleve a cabo la instalación sin contratiempos.

Certified to comply with ANSI A112.18.1

Certificación de cumplimiento de la norma ANSI A112.18.1 Certifié conforme à ANSI A112.18.1

Nous vous remercions d’avoir choisi American Standard… synonyme de qualité supérieure depuis plus de 100 ans. Pour vous assurer que l’installation se déroulera sans difficulté, veuillez lire attentivement ces instructions avant de commencer.

U.S. Patent No. D403,750
Patente estadounidense D403,750
Brevet U.S.A. no. D403,750	M 9 6 8 3 8 5 C

Recommended Tools & Materials/Herramientas y Materiales Recomendados/Outils et matériaux recommandés

10'

	Drill	Regular Screwdriver	Phillips Screwdriver
Tape Measure	Taladro	Desarmador plano	Desarmador de cruz
Flexómetro	Perceuse	Tournevis plat	Tournevis cruciforme
Ruban à mesurer
1 INSTALL MOUNTING PLATES

The TISSUE HOLDER (1) works best if secured to a wall stud or cross brace within the wall, using the SCREWS (3) supplied. If the TISSUE HOLDER (1) is to be installed on a tile or plaster wall the ANCHORS (4) and SCREWS (3) should be used.

Note: The center line distance (6-1/4") between the MOUNTING PLATES (5) is critical, and must be maintained.

Determine desired height and location (optional) and mark a center line. Using the MOUNTING PLATE (5) as a template mark the two spots for the anchors. If MOUNTING PLATE (5) is secured to a stud or cross brace drill small pilot holes for SCREWS (3).

For installations on drywall, use ANCHORS (4) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the wall. The TISSUE HOLDER BODIES (2) are mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over ANCHORS (4) and insert screws provided with #2 Phillips screwdriver. See illustration below. Repeat above steps for remaining MOUNTING PLATES (5).

For installations on tiled walls, pre drill a 1/4" hole through the tile only. Do not drill into the drywall. Use ANCHORS (4) and SCREWS (3) for securing MOUNTING PLATE (5) to tiled wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the tiled wall. The TISSUE HOLDER BODIES (2) are mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over ANCHORS (4) and insert screws provided with #2 Phillips screwdriver. See illustration below. Repeat above steps for remaining MOUNTING PLATES (5).

Secure MOUNTING PLATE (5) to wall with SCREWS (3).

	6-1/4"
6-1/4" (159 mm)
159 mm (6-1/4 po.)		CENTER LINE	1
		LÍNEA CENTRAL
		LIGNE CENTRALE

USE MOUNTING PLATE AS TEMPLATE	3	2
USE LA PLACA DE MONTAJE COMO PLANTILLA

UTILISER UNE PLAQUE DE MONTAGE COMME GUIDE

3 5 4

CENTER LINE LÍNEA CENTRAL LIGNE CENTRALE

4

5

FINISHED WALL

PARED TERMINADA

MUR FINI