American Standard 2901EC dimensions SAVONA ELITE 6’, Whirlpools By American Standard

SAVONA ELITE™ 6’

WHIRLPOOLS BY AMERICAN STANDARD

HIGH GLOSS ACRYLIC

		1810mm		19mm
		(71-1/4)
				(3/4)
	905mm	IN-LINE HEATER
				TYP.
	(35-5/8)	REMOVABLE
		BLANK
1105mm	552mm			PUMP
	(21-3/4)			OUTLINE OF
(43-1/2)
		C/L		1772mm X
				1067mm
				(69-3/4 X 42)
				CUTOUT
		178mm
		(7)
305mm	140mm
(12)
	(5-1/2)
				ON/OFF
C/L OF 1-1/2 O.D.		229mm X 305mm		SWITCH
DRAIN OUTLET
		(9 X 12) FLOOR
	● RECOMMENDED
	FITTING LOCATION	CUTOUT	PROVIDE ACCESS
	64 X 279mm (2-1/2 X 11)
			TO PUMP FOR SERVICE
		C/L OF OVERFLOW	ON ALL INSTALLATIONS
	38mm		■ LEVELING STRINGER
		89mm
				NOT FOR SUPPORT
51mm	(1-1/2)
		(3-1/2)
(2)
				559mm
				(22)
				508mm
				(20)
	INTEGRAL
	FEET

44 mm

(1-3/4)

89 mm (3-1/2)

1-1/2 O.D. TAILPIECE

ROUGH

FLOOR

1-1/2 N.P.T.M.

THREADS

GENERAL SPECIFICATIONS FOR 2901E WHIRLPOOL

INSTALLED SIZE		71-1/4 x 43-1/2 x 22 In.(1810 x 1105 x 559mm)
WEIGHT					152 Lbs. (68 Kg.)
WEIGHT w/WATER					936 Lbs. (421 Kg.)
GAL. TO OVERFLOW					94 Gal. (356 L)
WHIRLPOOL MIN. OPERATING VOL.					86 Gal.(326 L)
BATHING WELL AT SUMP				44 x 28 In. (1118 x 711mm)
BATHING WELL AT RIM			67-1/2 x 33 In. (1715 x 838mm)
WATER DEPTH TO OVERFLOW					16-1/4 In. (413mm)
FLOOR LOADING			43 Lbs./Sq.Ft. (211 Kgs./Sq.m)
(PROJECTED AREA)
PTS.			27.8
CUBE (FT3)						61.5
	WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP					2.1 HP, 14.4 AMPS, 120V.

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIALS BY OTHERS.

●IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING AND DRAIN OVERFLOW. MOUNTING HOLES DRILLED BY INSTALLER.

OPTIONAL TILING BEAD KIT No. TILE-BEAD AVAILABLE AND MUST BE ORDERED SEPARATELY.

■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION. FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 / CSA Certified. These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

© 2003 American Standard Inc.