American Standard 738520-0070A, 3520.000 dimensions Ravenna Semi-Pedestalsink, Nominal Dimensions

RAVENNA™

SEMI-PEDESTAL SINK

VITREOUS CHINA

RAVENNA™ WALL-HUNG

SEMI-PEDESTAL LAVATORY

•Vitreous china

•Contemporary design wall-hung with semi-pedestal P-trap cover for ease of cleaning

•Rear overflow

•Soap and accessory deck

•Optional with integral mounted towel bar (ordered separately)

•Supplied with mounting kit

•Design matched to Ravenna toilets (faucet shown not included)

•Faucet ledge with generous shelf area for accessories

❏ 0268.444 Faucet holes on 4" (102mm) centers

	(shown)	20"
❏	0268.888 Faucet holes on 8" (203mm) centers			3-1/4"	FINISHED
		(508mm)
				(83mm)	WALL
❏	0268.144 Center hole only		4"
			(102mm)
Nominal Dimensions:					7-3/4"
					(197mm)

24-1/4" x 19-1/2" x 34"

(616 x 495 x 864mm)19-1/2"

(495mm)

	SEMI-PED
Separate Components:	BASE
	1-3/4" DIA.
❏ 0268.004 Lavatory slab 4" (102mm) centers	STD. DRAIN
	OUTLET

❏ 0268.008 Lavatory slab 8" (203mm) centers	TOWEL
	RAIL	24-1/4"		1/2" (13mm) DIA.
❏ 0268.001 Lavatory slab center hole only
		(616mm)		SEMI-PED ANCHOR
❏ 0044.000 Semi-pedestal leg	2"	9-1/2"		SCREW HOLES ON
	(51mm)			4-1/4" (108mm) CTRS
		(241mm)
Recommended Components:	8-1/4"
❏ 3520.000 Integral Towel Bar	(210mm)
002 Chrome, 295 Satin Nickel	7/8" (22mm) DIA.	2-3/4"
❏ 738520-0070ATowel Bar mounting kit		(70mm)	SUPPLIES AS
	SLAB ANCHOR
			REQUIRED
	SCREW HOLES ON		1-1/4" O.D.	34"
	9-1/2" (241mm) CTRS
			WASTE	(864mm)
Bowl sizes:
			1-1/4" O.D.
19" (483mm) wide			TAILPIECE
		*21"	5"	*24-3/4"
12" (305mm) front to back		(533mm)	(127mm)	(629mm)
6" (152mm) deep		14-3/8"
		(365mm)
	FINISHED
Compliance Certifications:	FLOOR
Meets or exceeds the following specifications:

• ASME A112.19.2 for vitreous china fixtures	NOTES:
	* DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE
	SUGGESTED.
To Be Specified:	▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.
	■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST
❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black	BE TAKEN FROM FIXTURE.
	FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
❏ Faucet*:	PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.
❏ Faucet Finish:	INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.
❏ Supplies:	IMPORTANT: Dimensions of fixtures are nominal and may vary within the
❏ 1-1/4" Trap	range of tolerances established by ANSI Standard A112.19.2.
	These measurements are subject to change or cancellation. No responsibility
	is assumed for use of superseded or voided pages.
* See faucet section for additional models available
	J60
© 2008 AS America Inc.		Revised 5/06