American Standard 3572.018WC.K2 dimensions GREEN TEA 5-1/2x WHIRLPOOL AND BATHING POOL, High Gloss

GREEN TEA™ 5-1/2' x 36"

WHIRLPOOL AND BATHING POOL

HIGH GLOSS

		66
		(1676mm)	14-3/4
			(292mm)
OUTLINE OF CUTOUT 64.5 x 34.5 (1638 x 876mm)			11-1/2
			(292mm)
PUMP			36
			(914mm)
		9	C
		(229mm)	L
	CUTOUT IN FLOOR FOR DRAIN
PROVIDE ACCESS TO PUMP FOR		(2) AIR VALVES
SERVICE ON ALL INSTALLATIONS		ON/OFF
C/L OF OVERFLOW		SWITCH
			2
4	LEVELING STRINGER NOT
(102mm)			(51mm)
	FOR SUPPORT
			19
	21	(483mm)
			SAFE-T-HEATER
ROUGH (533mm)
			REMOVABLE
FLOOR
			BLANK
INTEGRAL FEET

66

(1676mm)14-3/4(292mm)

OUTLINE OF CUTOUT 64.5 x 34.5 (1638 x 876mm)		11-1/2
	(292mm)

36

(914mm)

9	C
(229mm)	L

CUTOUT IN FLOOR FOR DRAIN

C/L OF OVERFLOW		2
4	LEVELING STRINGER NOT
(102mm)	FOR SUPPORT	(51mm)
		19
	21	(483mm)
ROUGH (533mm)
FLOOR
INTEGRAL FEET

GENERAL SPECIFICATIONS FOR 3572 WHIRLPOOL

INSTALLED SIZE	66 x 36 x 21 In. (1676 x 914 x 533mm)
WEIGHT					100 Lbs. (45 Kg.)
WEIGHT w/WATER					592 Lbs. (269 Kg.)
GAL. TO OVERFLOW						59 Gal. (223 L.)
MIN. OPERATING GAL.						44 Gal. (167 L.)
BATHING WELL AT SUMP				19 x 49 In. (483mm x 1245mm)
BATHING WELL AT RIM		54-1/2 x 27 In. (1384mm x 686mm)
WATER DEPTH TO OVERFLOW							14 In. (356mm)
FLOOR LOADING			36 Lbs./Sq. Ft. (175 Kgs/Sq. m.)
(PROJECTED AREA)
PTS.									25.6
CUBE (FT3)								45.1

WHIRLPOOL ELECTRICAL SPECIFICATIONS

SYSTEM I PUMP 1.4 HP, 7.5 AMPS, 120V.

NOTES:

GENERAL SPECIFICATIONS FOR 3572 BATHING POOL

INSTALLED SIZE	66 x 36 x 21 In. (1676 x 914 x 533mm)
WEIGHT						66 Lbs. (30 Kg.)
WEIGHT w/WATER					557 Lbs. (253 Kg.)
GAL. TO OVERFLOW						59 Gal. (223 L.)
BATHING WELL AT SUMP				19 x 49 In. (483mm x 1245mm)
BATHING WELL AT RIM		54-1/2 x 27 In. (1384mm x 686mm)
WATER DEPTH TO OVERFLOW							14 In. (356mm)
FLOOR LOADING			34 Lbs./Sq. Ft. (165 Kgs/Sq. m.)
(PROJECTED AREA)
PTS.									25.6
CUBE (FT3)								45.1

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.

■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION. OPTIONAL 3 WALL TILING BEAD. KIT AVAILABLE AND MUST BE ORDERED SEPARATELY.

●FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

●IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

	H4
© 2008 AS America Inc.		Rev. 2/08