| Installation | |
ACCESSORIES | Instructions | |
6028.230 | 6090 | |
TOILET TISSUE HOLDER | 6028.180 | 6091 |
18"TOWEL BAR | 6028.244 | 6092 |
24"TOWEL BAR | 6028.024 | 6093 |
GLASS SHELF | ||
Thank you for selecting | ||
of fine quality for over 100 years. |
| |
To ensure that your installation proceeds | ||
read instructions carefully before you begin. | M968860 REV . 1 . 1 | |
|
| |
Recommended Tools
10' | Tape Measure | Regular Screwdriver |
|
Drill
Phillips Screwdriver Level
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A COARSE SURFACE.
1 | 18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF AND TOILET TISSUE HOLDER |
MOUNTING BRACKET INSTALLATION |
The 18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF and TOILET TISSUE HOLDER work best if secured to a wall stud or cross brace within the wall, using the SCREWS (4) supplied.
If the 18" TOWEL BAR, 24" TOWEL BAR, GLASS SHELF and TOILET TISSUE HOLDER are to be installed on a tile or plaster wall the ANCHORS and SCREWS should be used.
Determine desired height and location (optional) for the accessory and mark a center line. Use the full size template supplied to mark hole locations for the mounting brackets. For the 24" TOWEL BAR and GLASS SHELF use 24” template. For 18” TOWEL BAR use 18” template. For the TOILET TISSUE HOLDER use the 7” template. If MOUNTING BRACKET (1) is secured to a stud or cross brace drill small pilot holes for SCREWS (2).
For installations on drywall, use DRYWALL ANCHOR (3) and SCREWS (2) for securing MOUNTING BRACKETS (1) to wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the wall. Place MOUNTING BRACKET (1) over DRYWALL ANCHORS (3) and insert screws provided with #2 Phillips screwdriver. See illustration below. Secure MOUNTING BRACKETS (1) to wall with SCREWS (2).
For installations on tiled walls, If TILE ANCHORS (4) and SCREWS (2) are used for securing MOUNTING BRACKET (1), then drill two 1/4" diameter holes a minimum of
Secure MOUNTING PLATES (1) to wall with SCREWS (2).
2 |
| 1a |
|
INSTALL 18" TOWEL BAR, AND 24" TOWEL BAR | 5a | CENTER | |
| LEVEL | ||
|
|
| LINE |
| Place right ESCUTCHEON (5) onto MOUNTING BRACKET (1), and secure | 6 | 1 |
| with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied. |
|
|
Insert each end of TOWEL BAR (8) into the CRANKS (9).
Place LEFT ESCUTCHEON (5a) onto MOUNTING BRACKET (1a) and | 9 | 8 |
| ||||
secure with SET SCREW (6) using 2.5 mm HEX WRENCH (7) supplied. |
| 5 | |||||
|
| ||||||
|
| 6092 | 24" | 6093 |
|
| 6 |
|
| GLASS SHELF | 24" TOWEL BAR |
|
| ||
| 18" |
|
|
|
| CENTER LINE |
|
7" | 6091 |
|
| FINISHED WALL |
|
| |
18" TOWEL BAR | CENTER LINE |
|
| (OPTIONAL TO |
| ||
6090 |
|
|
|
|
| FINISHED FLOOR) | 9 |
TOILET TISSUE HOLDER |
|
|
|
|
| ||
|
|
|
|
|
|
| |
|
| DRILL PILOT HOLE FOR |
|
|
|
| 7 |
|
| WOOD SCREW OR |
|
|
|
| |
|
| 1/4" DIA. HOLE FOR |
|
|
|
| |
|
| ANCHOR |
| TEMPLATE |
|
| |
|
| ANCHORS (FOR TILED WALLS) |
|
|
| ||
|
| DRYWALL ANCHORS |
|
|
|
|
|
|
|
| FINISHED WALL |
1 | CENTER | 3 | 5 5a |
LINE | 4 | ||
2 |
|
| 1 |
|
|
| |
4 | DRILL PILOT HOLE FOR |
|
|
WOOD SCREW (1) OR |
|
| |
3 | 1/4" DIA. HOLE FOR |
| 6 |
ANCHOR (4) |
| ||
SLOT |
|
|
|
