STOPPER INSTALLATION PROCEDURE
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable).
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice |
|
|
|
|
|
|
|
|
|
|
| Fig. G. | |
that the Loop is on one side of the Stopper. Fig. G. |
|
|
|
|
|
|
|
|
|
|
| ||
To install the stopper in “Locked” mode, insert the Stopper into | LOGO |
|
|
|
|
|
|
|
| ||||
|
|
|
| ||||||||||
the Drain so that the Plastic Loop is facing toward the rear of the |
|
|
|
|
|
|
|
|
|
|
|
|
|
Sink and the American Standard logo is facing front. Rotate |
|
|
|
|
|
|
|
|
|
|
|
|
|
Stopper slightly if necessary so that the Stopper slides all the |
|
|
|
|
|
|
|
|
|
|
|
|
|
way down.Fig. G. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
to make sure it is fully inserted. Fig. J. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| LOOP TOWARD |
| ||
|
|
|
|
|
|
|
|
|
| REAR OF SINK |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |
outward. If the Cam Cap does not “snap” into place, then rotate |
|
|
|
|
|
|
|
|
|
| DRAIN | ||
the Cam to make sure it is fully inserted. Fig. K. |
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
| Locked Mode | ||||||||||
Troubling Shooting Guide to complete installation. Stopper will be |
|
|
| ||||||||||
|
| (Vandal Proof) | |||||||||||
in “Locked” mode and not be removable. |
|
| |||||||||||
Unlocked Mode: |
|
|
|
|
|
|
|
|
|
|
|
|
|
Look at the Plastic Loop at the bottom of the Stopper and notice |
|
|
|
|
|
|
|
|
|
|
|
|
|
that the Loop is on one side of the Stopper. Fig. H. |
|
|
|
|
|
|
|
|
|
|
| Fig. H. | |
To install the stopper in “Unlocked” mode, insert the Stopper into | LOGO |
|
|
|
| ||||||||
|
|
|
|
| |||||||||
| |||||||||||||
the Drain so that the Plastic Loop is facing toward the front of the |
|
|
|
|
|
|
|
|
|
|
|
|
|
Sink and the American Standard logo is facing rear. Rotate Stopper |
|
|
|
|
|
|
|
|
|
|
|
|
|
slightly if necessary so that the Stopper slides all the way down. |
|
|
|
|
|
|
|
|
|
|
|
|
|
Fig. H. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 180˚ | |||
|
|
|
|
|
|
|
|
|
|
|
|
| |
to make sure it is fully inserted. Fig. J. |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| LOOP TOWARD |
| ||||
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| FRONT OF SINK |
| ||||
outward. If the Cam Cap does not “snap” into place, then rotate |
|
|
|
|
|
|
|
|
|
|
|
|
|
the Cam to make sure it is fully inserted. Fig. K. |
|
|
|
|
|
|
|
| DRAIN |
“Troublingshooting Guide” to complete installation. Stopper will beUnlocked Mode in “Unlocked” mode and removable.
Fig. J.
CAM
Fig. K.
INSTALL CAM
INSTALL CAM CAP
M968892 Rev . 1 . 1
6