1
CAUTION
Turn off hot and cold water supplies before beginning.
SWING SPOUT ASSEMBLY
Apply the grease (provided) liberally to the SPOUT
Assemble the SPOUT and tighten the SPOUT NUT until snug on VALVE BODY.
SPOUT
SPOUT
NUT
SNAP
RING
SPOUT
2 FITTING INSTALLATION
Remove LOCKNUT, BRASS WASHER, and RUBBER WASHER from fitting.
Place RUBBER RING in recess of fitting.
Insert inlet tubes (on model 7190 only) and THREADED SHANK through hole of sink making certain RUBBER RING is properly seated in the recess of the fitting base.
Assemble RUBBER WASHER, BRASS WASHER, and LOCKNUT onto the THREADED SHANK from underside of sink deck.
Tighten the LOCKNUT securely.
For Model 7190 Only
Bend the inlet tubes to meet the supply lines.
NOTE: Use the palm of your hand to support the inlet tubes during bending to avoid kinking of the tubes.
Connect the hot water supply line to the left inlet tube and the cold water supply line to the right inlet tube using appropriate connectors.
For Model 7100 Only
Connect hot or cold water supply lines to shank using sealant, appropriate connectors, and coupling nuts.
MODEL 7190 | MODEL 7100 |
RECESS
| RUBBER |
RECESS | RING |
| |
| SHANK |
| RUBBER |
| MOUNTING |
| WASHER |
| BRASS |
| WASHER |
HOT | LOCKNUT |
COPPER |
| SUPPLY | |
INLET TUBES |
| ||
COLD | NUT | ||
| |||
|
|
3 TEST INSTALLED FAUCET
Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks.
Remove AERATOR.
With handle in OFF position, turn on water supplies and check all connections for leaks.
4 SERVICE
To change direction of handle rotation, proceed as follows:
Turn handles into OFF position and replace AERATOR.
AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90° .
| Turn valve to OFF position. | SPRING |
| Remove INSERT and HANDLE SCREW. | |
| ||
| CLIP | |
| Slip HANDLE with ADAPTER off. | |
| ||
|
|
| Remove SPRING CLIP. | STOP |
| ||
| ||
| Lift STOP WASHER, turn 90° and replace. | WASHER |
| ||
| ||
| Replace SPRING CLIP. |
|
|
| |
|
| |
| Replace ADAPTER, HANDLE, SCREW, and INSERT. |
|
|
| |
|
|
HOTLINE FOR HELP
For
1 (800)
Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:
Remove INSERT and HANDLE SCREW. Slip HANDLE with ADAPTER off. Unscrew CARTRIDGE with wrench. Thoroughly rinse plastic SCREEN at base of CARTRIDGE.
Replace CARTRIDGE until flange is tight against valve body.
Turn valves OFF.
Replace ADAPTER, HANDLE, SCREW, and INSERT.
CARTRIDGE
SCREEN
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time
IN CANADA
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . C A m e r i c a n S t a n d a r d I n c . 1 9 9 9
3 4 4 4 0 N