American Standard 7236.028WC dimensions Virtuoso Whirlpool, High Gloss, Revised 2/08

VIRTUOSO™ WHIRLPOOL

HIGH GLOSS

CUTOUT X 876mm	X 34-1/2)
OUTLINE OF 1791mm	(70-1/2

		1829mm
	914mm	(72)		19mm
(36)			(3/4)
				TYP.

914mm

(36)
			PUMP		ACCESSPROVIDE SERVICEFORPUMPTO INSTALLATIONSALLON
	C/L OF	102mm	178mm X 356mm
			(7 x 14) CUTOUT
	DRAIN	(4)	470mm
279mm			(18-1/2)
(11)			RECOMMENDED	ON/ OFF
				SWITCH
			FITTING LOCATION
			64 X 279mm (2-1/2 X 11)
C/L OF		SAFE-T-HEATER
OVERFLOW				51mm
		REMOVABLE BLANK
				(2)
76mm
(3)
				489mm
				(19-1/4)
			LEVELING		540mm
44mm			STRINGER
					21-1/4
			NOT FOR
(1-3/4)
			SUPPORT
89mm			ROUGH FLOOR
	1-1/2 N.P.T. THREAD		INTEGRAL
(3-1/2)			FEET
	1-1/2 O.D.

TAILPIECE

GENERAL SPECIFICATIONS FOR 7236 WHIRLPOOL

INSTALLED SIZE	72 x 36 x 21-1/4 In. (1829 x 914 x 540mm)
WEIGHT		101 Lbs. (45 Kg.)
WEIGHT w/WATER		751 Lbs. (338 Kg.)
GAL. TO OVERFLOW		78 Gal. (296 L)
WHIRLPOOL MIN. OPERATING VOL.		69 Gal. (262 L)
BATHING WELL AT SUMP		46 x 18 In. (1168 x 457mm)
BATHING WELL AT RIM		66 x 30-1/2 In. (1676 x 775mm)
WATER DEPTH TO OVERFLOW		15-3/4 In.(400mm)
FLOOR LOADING		42 Lbs./Sq.Ft. (204 Kgs./Sq.m)
(PROJECTED AREA)
PTS.		25.6
CUBE (FT3)		49.4
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM II PUMP		2.1 HP,15.6 AMPS,120V.

NOTES:

BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND OR PENINSULA TYPE INSTALLATION. SUMP OF BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.

■REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL, DECK MOUNTED SPOUT AND INTEGRATED BATH FILLER FOR ADDITIONAL INFORMATION.

OPTIONAL 3-WALL TILING BEAD KIT NO. 751755-100 AND APRON No. 0727.200 MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.

●FITTINGS AND TWIST GRAB BAR NO. 750565-000 NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

●IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.

ON SYSTEM II: CONTROL MODULE TO BE MOUNTED BEHIND ACCESS PANEL, A MINIMUM OF 152mm (6) ABOVE ROUGH FLOOR.

IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1 These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided leaflet.

	H42
© 2008 AS America Inc.		Revised 2/08