SAVONA™
PEDESTAL SINK
VITREOUS CHINA
SAVONA™ PEDESTAL SINK
•
•Made from vitreous china
•Convenient soap/accessory ledge
•Rear overflow
•Design-matched to Savona toilets
•Supplied with mounting kit
•Shown with 3801.432 Jasmine Spread Lavatory Faucet with Perfume Bottle Handles (not included)
❏0156.803 Faucet holes on 8" (203mm) centers
Nominal Dimensions: 635 x 502 x 864mm (25" x
Separate Components:
❏0156.008 Pedestal
❏
Bowl sizes:
464mm
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2M for Vitreous China Fixtures
To Be Specified: |
|
❏ Color: ❏ White | ❏ Bone ❏ Linen |
❏ Silver | ❏ Fawn Beige ❏ Black |
❏Faucet*:
❏Faucet Finish:
❏Supplies:
❏
* See faucet section for additional models available
| 572mm |
| |
|
| ||
| 203mm | FINISHED | |
| WALL | ||
70mm | (8) | ||
| |||
|
| ||
140 mm |
| 216mm | |
| |||
|
|
PEDESTAL TO
WALL CLEARANCE
|
|
| 502mm |
| |
PEDESTAL ANCHORING |
|
|
| ||
|
|
|
|
| |
SCREW HOLES |
|
|
|
|
|
8mm (5/16) DIA. |
|
|
|
|
|
|
| 635mm | FITTING |
| 70mm |
|
| DECK |
| ||
| 241mm | (25) |
| ||
|
|
|
| ||
|
| 35mm |
|
| |
|
|
|
| ||
| REF. |
|
|
| |
|
|
|
|
| DRAIN |
197mm |
|
|
|
| CHASE |
|
|
|
|
| |
C/L |
|
|
|
| |
| 19mm (3/4) DIA. |
|
| ||
|
|
|
| ||
| 203mm | HOLES FOR | 864mm | ||
| ANCHOR BOLTS | ||||
| (8) | (34) |
| ||
178mm |
|
|
| ||
|
|
| REF. |
| |
(7) |
|
|
|
| |
|
|
|
|
| |
|
| SUPPLIES AS |
|
| |
| *527mm | REQUIRED | *584mm |
| |
| OPEN | ||||
| WASTE | (23) |
| TO | |
|
|
|
|
| FLOOR |
FINISHED |
|
|
|
| |
FLOOR |
| TAILPIECE |
|
|
|
| 178mm |
|
|
|
|
| (7) |
|
|
|
|
| NOTES: | ||
| * DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE | ||
| SUGGESTED. | ||
| ▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED. | ||
| ■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST | ||
| BE TAKEN FROM FIXTURE. | ||
| FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY. | ||
| PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS. | ||
| INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY. | ||
| IMPORTANT: Dimensions of fixtures are nominal and may vary within the | ||
| range of tolerances established by ANSI Standard A112.19.2. | ||
| These measurements are subject to change or cancellation. No responsibility | ||
| is assumed for use of superseded or voided pages | ||
| J6 |
| |
© 2008 AS America Inc. | Revised 2/08 | ||
|