American Standard 7500 Series, 7501 Series Grid Drain Assembly, Test Installed Faucet, Service

1
		Turn off hot and cold water
	CAUTION
		supplies before beginning.

Asesemble GASKET to SHANKS and insert FAUCET SHANKS through holes of SINK.

Assemble RUBBER and BRASS WASHERS, and LOCKNUTS from underside of SINK. Drop UPPER LIFT ROD through hole in BODY (models 7501 only), align BODY as far forward as possible and secure position by tightening LOCKNUTS.

Connect the HOT water supply to the left SHANK and the COLD water supply to the right SHANK using sealant, appropriate connectors, and COUPLING NUTS.

To change spout to a swivel spout:

UPPER LIFT ROD

SPOUT

SPOUT NUT

RUBBER

RING

SPOUT

CLIP

Unscrew SPOUT NUT and remove SPOUT.

Take SPOUT CLIP off SPOUT and remove RUBBER RING.

Replace RUBBER RING with seperate PLASTIC RING packed with faucet.

Put SPOUT CLIP on SPOUT.

Reassemble SPOUT to BODY.

2	GRID DRAIN ASSEMBLY	FLANGE
	(Model 7502 only)	PUTTY
	Apply a bead of PUTTY around underside	SINK
	of DRAIN PLUG flange. Insert DRAIN	DRAIN
	PLUG into SINK drain hole.
		PLUG
	Hold DRAIN PLUG to prevent turning	RUBBER
	and assemble GASKET, WASHER, and	GASKET
	LOCKNUT, from underneath sink.	WASHER
	Insert threaded end of TAILPIECE	LOCKNUT
	into lower end of DRAIN PLUG.	TAIL
	Connect other end to trap.
		PIECE

BODY

GASKET

SINK

HOT

PLASTIC

RING

SHANK

1/2" O.D. SLIP

RUBBER WASHER

BRASS WASHER

LOCKNUT

COLD

COUPLING NUT

3 INSTALL POP-UP DRAIN (Model 7501 only)

Push TAILPIECE down into TRAP (threaded end up).

Thread LOCKNUT, WASHER and

GASKET onto DRAIN BODY.

Apply a bead of PUTTY to underside of FLANGE.

Feed DRAIN BODY up through SINK and thread FLANGE fully onto BODY.

Tighten LOCKNUT firmly, keeping the PIVOT ROD pointed towards the back of the SINK.

Drop STOPPER into DRAIN BODY.

Pull TAILPIECE up and thread tightly into DRAIN BODY.

STOPPER

FLANGE

SINK

	PUTTY
	GASKET
	WASHER
LOCKNUT	CLIP
	PIVOT
	ROD
	TAILPIECE
	TRAP

Position EXTENSION ROD onto POP-UP ROD and tighten THUMBSCREW.

Remove one end of CLIP from PIVOT ROD by squeezing ends together while sliding.

Insert PIVOT ROD into second or third hole in EXTENSION and reassemble CLIP. (EXTENSION may need to be bent.)

THUMBSCREW	POP-UP ROD
PIVOT	EXTENSION ROD
ROD
	CLIP
DRAIN	TAILPIECE
BODY

Adjust STOPPER height by repositioning EXTENSION and tightening THUMBSCREW.

4 TEST INSTALLED FAUCET

Remove AERATOR.

With handle in OFF position, turn on water supplies and check all connections for leaks.

5 SERVICE	90°
	STOP
To change direction of handle rotation,	WASHER
	SPRING

Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks.

Operate LIFT ROD and check DRAIN for leaks.

Turn handles into OFF position and replace AERATOR.

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.

proceed as follows: CLIP

Turn valve to OFF position.

Remove HANDLE and BONNET NUT.

Remove SPRING CLIP.

Lift STOP WASHER, turn 90° and replace.

Replace SPRING CLIP.

Replace BONNET NUT, HANDLE, SCREW, and INDEX.

AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.

HOTLINE FOR HELP

For toll-free information and answers to your questions, call:

Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:

Remove HANDLE and BONNET NUT. Remove CARTRIDGE by pulling up. Thoroughly rinse plastic SCREEN at base of CARTRIDGE.

Replace CARTRIDGE until flange is tight against valve body.

Turn valves OFF.

Replace BONNET NUT, HANDLE, SCREW and INDEX.

CARTRIDGE

SCREEN

1 (800) 223-0068

Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c . C A m e r i c a n S t a n d a r d I n c . 1 9 9 5

6 0 1 8 5