Installation Instructions

Instrucciones de instalación

Mode d’installation

8040.230 SERIES SERIE 8040.230 SÉRIE 8040.230

TISSUE HOLDER

SOPORTE PARA PAPEL HIGIÉNICO SUPPORT DE PAPIER TOILETTE

Thank you for selecting American-Standard...the benchmark of fine

quality for over 100 years. To ensure that your installation proceeds smoothly-- please read these instructions carefully before you begin.

Gracias por seleccionar los productos American Standard, sinónimo de la mejor calidad durante más de 100 años. Por favor lea estas instrucciones detenidamente antes de comenzar para que lleve a cabo la instalación sin contratiempos.

Nous vous remercions d’avoir choisi American Standard… synonyme de qualité supérieure depuis plus de 100 ans. Pour vous assurer que l’installation se déroulera sans difficulté, veuillez lire attentivement ces instructions avant de commencer.

Certified to comply with ANSI A112.18.1 Certificación de cumplimiento de la norma Certifié conforme à ANSI A112.18.1

U.S. Patent No. D403,750 Patente estadounidense D403,750 Brevet U.S.A. no. D403,750

ANSI A112.18.1

M 9 6 8 7 4 2 D

Recommended Tools & Materials/Herramientas y Materiales Recomendados/Outils et matériaux recommandés

10'

 

Drill

Regular Screwdriver

Phillips Screwdriver

Tape Measure

Taladro

Desarmador plano

Desarmador de cruz

Flexómetro

Perceuse

Tournevis plat

Tournevis cruciforme

Ruban à mesurer

 

 

 

1 INSTALL MOUNTING PLATES

 

 

 

The TISSUE HOLDER (1) works best if secured to a wall stud or cross brace within the wall, using the SCREWS (3) supplied. If the TISSUE HOLDER (1) is to be installed on a tile or plaster wall the ANCHORS (4) and SCREWS (3) should be used.

Note: The center line distance (6-1/4") between the MOUNTING PLATES (5) is critical, and must be maintained.

Determine desired height and location (optional) and mark a center line. Using the MOUNTING PLATE (5) as a template mark the two spots for the mounting holes. If MOUNTING PLATE (5) is secured to a stud or cross brace drill small pilot holes for SCREWS (3).

For installations on drywall, use ANCHORS (4) and SCREWS (3) for securing MOUNTING PLATE (5) to wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the wall. The TISSUE HOLDER BODIES (2) are mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over ANCHORS (4) and insert screws provided with #2 Phillips screwdriver. See illustration below. Repeat above steps for remaining MOUNTING PLATES (5).

For installations on tiled walls, pre drill a 1/4" hole through the tile only. Do not drill into the drywall. Use ANCHORS (4) and SCREWS (3) for securing MOUNTING PLATE (5) to tiled wall. Place #2 Phillips screwdriver or cordless screwdriver into recess of anchor. Press into drywall while turning the anchor clockwise until it is seated flush with the tiled wall. The TISSUE HOLDER BODIES (2) are mounted 6-1/4" center to center. Place MOUNTING PLATE (5) over ANCHORS (4) and insert screws provided with #2 Phillips screwdriver. See illustration below. Repeat above steps for remaining MOUNTING PLATES (5).

Secure MOUNTING PLATE (5) to wall with SCREWS (3).

 

6-1/4"

 

 

 

 

 

 

 

6-1/4" (159 mm)

 

 

159 mm (6-1/4 po.)

CENTER LINE

1

 

 

 

 

 

 

LÍNEA CENTRAL

 

 

 

 

 

 

 

LIGNE CENTRALE

 

USE MOUNTING PLATE AS TEMPLATE

3

2

USE LA PLACA DE MONTAJE COMO PLANTILLA

 

UTILISER UNE PLAQUE DE MONTAGE COMME GUIDE

3 5 4

CENTER LINE LÍNEA CENTRAL LIGNE CENTRALE

4

5

FINISHED WALL

PARED TERMINADA

MUR FINI

Page 1
Image 1
American Standard 8040.230 installation instructions Install Mounting Plates, 4 159 mm Mm 6-1/4 po