American Standard 9205.024.339 Option, Care and Cleaning of Vanity, Diagram of OPTION

GRID

DRAIN BODY

Optional Laminate Marble Top Installation

NOTE: Tops are precut to accommodate recommended sinks and faucet.

OPTION 1:		OPTION 2:
		China Rectangular Sink – Refer to instructions
Glass Vessel or Round China Vessel
		supplied with rectangular vessel.
1	Place the riser (“O” Ring side down) over the hole in countertop	Diagram of OPTION 1
	surface. Position Glass Vessel onto riser aligning holes.
2	The sink is mounted and secured on the countertop by the grid
	drain assembly, which is installed as follows:	Laminate Marble Top w/
	1. Place the rubber gasket beneath the rim of the grid	Glass Vessel or
	drain body and insert drain through sink and riser.	China Round Vessel
	2. Install the washer and locknut onto the grid drain from
	beneath the countertop surface. Hand tighten.

3.Level sink front-to-back and side-to-side, then tighten (do not overtighten).

4. Install tail piece.

RUBBER

GASKET

SINK

	COUNTER	Diagram of OPTION 2
	SURFACE
	(TYPICAL)
	RISER
“O” RING		Rectangular Vessel Sink
CUTOUT		on Studio Vanity
	WASHER
	LOCKNUT
	TAILPIECE
		Care and Cleaning of Vanity
3 Apply a bead of silicon adhesive to the rim of the vanity. Place		Clean the product by using soft, slightly damp cloth. Buff the product by using
the marble top centered left to right on the vanity and with the		a soft dry cloth. Avoid using silicone cleaners and waxes.
		Clean up excess water and spills immediately. Use a blotting rather than a
back edge of the top even with the rear of the vanity. Clean up
		wiping action. Water left over a long period of time will cause white spots in
any excess silicon.
		the finish.
		NOTE: Please note that some chemicals may damage the finish. Take care
4 Connect the trap to the		to avoid the following: iodine, hair dye, after shave lotion, shaving cream,
		alcohol, perfume, Lestoil®, Lysol Tub and Tile Cleaner®, Lysol Spray
drain assembly and hand		Disinfectant®, Dow Disinfectant®, acetone, paint remover, Formula 409®,
tighten to check	C	Tile-X®, and Nair®.
alignment. It may be
	B	Care and Cleaning of the Marble Vanity Top
necessary to cut off part of
the tail piece (area “B”) or		Marble is porous and easily stained. Wipe off anything spilled on it
part of the horizontal leg
		immediately. It should be washed or cleaned regularly with fresh warm water
of the trap (area “C”).		and a non-abrasive clean cloth. Also, using a non-abrasive, neutral (pH
		balanced) cleaner will help remove dirt and grime, but it is recommended to
		first try warm water only.
5 Install faucet and connect to supply in accordance with the		Marble should be sealed regularly with a good quality marble sealer. Marble
		sealers are available at most retail home supply stores. Follow the
manufacturer’s instructions.		instructions on the sealer container for proper application and frequency of
		use. The sealer acts as a stain inhibitor and prevents most stains and soil
		from being absorbed into the porous surface, but it is NOT a guarantee
		against staining. All spills should be cleaned immediately. Avoid contact with
6 Water test unit, check for leakage and correct as needed.		all oils and petroleum-based products. Also, avoid contact with all acid or
		caustic products such as vinegar, citrus or fruit juices, soda, chlorine, and nail
		polish remover. If the marble is well sealed, the warm water and non-abrasive
		cloth should keep it clean.
	-	3 -	770015-100