American Water Heater NRESS00408 Specification, Order Entry and Sales Warranty and Service

Residential Electric Lowboy

T&P VALVE

ACCESS

PANEL

ACCESS

PANEL

DRAIN

VALVE

ANODE

JUNCTION BOX

T&P VALVE

					HEIGHT TO	HEIGHT TO
		GPH		JACKET	TOP OF	SIDE T&P	APPROX.
	GALLON	RECOVERY		DIAMETER	HEATER	VALVE	SHIPPING
MODEL NUMBER	CAPACITY	90° RISE	EF	A	B	C	WEIGHT
E61-19L-045DV	19	20.7	N/A	16	31-1/4	24-1/4	60
E61-40L-045DV***	38	20.7	0.92	22	31-5/8	24-1/4	113
E61-50L-045DV***	46.5	20.7	0.91	24	31-5/8	24-1/4	133
E62-30L-045DV	28	20.7	0.93	22	29-1/2	22-1/2	84
E62-40L-045DV	38	20.7	0.92	24	31-5/8	24-1/4	113
E62-50L-045DV	46.5	20.7	0.91	26	31-5/8	24-1/4	133

To order single element substitute “S” for “D” in model number. Delete “V” from model number for top T&P option, T&P opening on top of the heater with the valve shipped in the box for field installation. All models include internal heat traps. Dimensions and specifications subject to change without notice in accordance with our policy of continuous product improvement. Dimensions on all charts shown in inches. All models are wired for non-simultaneous element operation. 3/4” water connection located on top. Top water connections are on 8” centers. ***Supplied with insulating jacket.

Specification

Residential electric water heater(s) shall be Lowboy model ____________ as manufactured by American Water Heaters, or an approved equal, and shall have a ______

-year tank warranty and a ______ -year parts warranty, when installed in a residential application. Heater(s) shall have a storage capacity of ______ gallons and shall have

a rated input of __________ KW at __________ Volts, single phase, 60 cycle AC, and shall be designed, tested and listed in accordance with Underwriter’s Laboratories

standard UL 174. Heaters shall meet or exceed the requirements of the Federal “National Appliance Energy Conservation Act of 1987” and shall comply with ASHRAE Standard 90.1-1999. The interior of the storage tank shall be lined with a Fused Ceramic Shield lining, fused to the tank at 1600°F, forming a corrosion-resistant lining; polymer linings are not acceptable. Each tank shall be furnished with an internal anode for cathodic protection. The unit must be equipped with a built-in electrical junction box. Electrical heating elements shall be screw-in, direct immersion, resistance type. Element operation shall be controlled by a thermostat for each element. A high temperature cut-off shall be supplied as an integral part of the heater. Element access panels shall be provided on the front of the heater for each element. A corrosion-resistant drain valve shall be provided on the front of each unit. The tank shall be totally encased in a metal jacket and insulated with a non-CFC foam to reduce standby heat loss. The tank must be design certified for 300 PSI test pressure and 150 PSI working pressure.

	Distributed By:
Order Entry and Sales	Warranty and Service
500 Princeton Road (FEDEX, UPS)	500 Princeton Road (FEDEX, UPS)
Johnson City, TN 37601-2030	Johnson City, TN 37601-2030
P.O. Box 4808 (Mailing)	P.O. Box 1597 (Mailing)
Johnson City, TN 37602-4808	Johnson City, TN 37605-1597
(800) 937-1037	(800)	999-9515
FAX (800) 581-7224	FAX (800)	999-5210

NRESS00408

No part of this work may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage retrieval system, without permission in writing from American Water Heaters.