Connecting Zone Outputs
Tango Controllers can be accessed by SWT Metreau keypads (DAS- MET6SRC and
Note: The Matrix Pushbutton
SWT Connectors
SWT cabling follows a specific pinout configuration that is labelled on the Tango Controller, Metreau keypads, and other Matrix devices, as shown in FIG. 3.
L | D | G | R | L = Left audio channel (+) |
|
|
|
| D = Data / Power (+) |
|
|
|
| G = Ground |
|
|
|
| R = Right audio channel (+) |
FIG. 3 SWT pinout configuration
Connecting Paging Inputs/Outputs
Paging Inputs are for Phone Systems or Communications Boxes. If the paging override is used, connect the paging Output connector on the Tango Controller to the Tango Zone Expander (FIG. 4):
Tango Audio Controller | Paging | |
| Out | |
From phone system or |
| |
communication box | Paging In | |
| ||
Tango Zone Expander (#1) | Paging | |
Out | ||
|
Paging In | To "Paging In" connector on | |
Tango Zone Expander #2 | ||
|
FIG. 4 Connecting Paging Input/Outputs
Connecting To Tango Audio Controllers
FIG. 5 provides a wiring diagram illustrating the connections between the Tango Audio Controller and multiple Tango Zone Expanders:
Audio Device (L/R)
3.Connect the source inputs. Patch each source from the source output on the Tango controller to the source inputs on the Zone Expander.
Note: Ensure the left and right source connections are properly matched and seated to the left and right terminals of the both the Tango Controller and the Zone Expander.
For example, Source 1 Output, on the Tango Controller to Source 1 Input on the Zone Expander).
Continue this procedure until each source is connected.
4.Paging Inputs are for Phone Systems or Communications Boxes. If the paging override is used, connect the paging output loop from the Tango Controller to the Zone Expander (see FIG. 5).
5.Connect the keypads to the Tango Controller and Zone Expander(s). Fol- lowing the same wiring code you used at each of the keypad locations, plug each SWT connector into the desired Zone Output connectors on the Tango Controller and Zone Expanders (see FIG. 5).
6.SWT Speakers connect to the Tango Controller via the SPEAKERS con- nector on the SWT keypads.
•Alternatively, you can terminate the speakers directly to the back of the Controller. Speakers connected directly to the zone output must be com- mon grounded.
•The minimum impedance for each zone should never be less than 4 ohms.
Note: Installing more than 2 pairs of speakers on any Zone output is not recommended without installing an external amplifier.
7.On the Main Controller, make the necessary NIC Port connections for the (optional) Network Interface Card and AM/FM Antennas.
8.Connect the power supply and power up the units.
Zone Expander Addressing
Use the Address switch on the rear panel of the Tango Zone Expanders (FIG. 6) to set the Address for each Expander, according to the values in the following table:
Address 1
FIG. 6 Address switch
Zone Expander # | Address | ||
|
| Zone) | (8 Zone) |
|
|
|
|
1 | 1 | Zones | Zones |
|
|
|
|
2 | 2 | Zones | Zones |
|
|
|
|
3 | 3 | Zones | Zones |
To Zones
To Zones
Audio
Controller
To Zones
RJ-11
Zone Expander #1
To Zones
Zone Expander #2
4 | 4 | Zones | Zones |
|
|
|
|
5 | 5 | Zones | Zones |
|
|
|
|
6 | 6 | Zones | Zones |
|
|
|
|
7 | 7 | Zones | Zones |
Additional Documentation
Additional documentation for Distributed Audio products is available online at www.amx.com:
•For details on Tango Audio Controllers, refer to the Tango Audio Control- lers Operation/Reference Guide and Installation Guide.
•For details on Metreau Keypads, refer to the Metreau Keypads Operation/ Reference Guide and Installation Guides.
•For details on Tango Amplifiers, refer to the Tango Amplifiers Installation Guide.
To Zones |
|
|
|
|
|
|
|
|
|
|
|
|
|
| To Zones |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
FIG. 5 Connecting the Tango Controller to Zone Expanders |
|
|
|
|
1.Connect the
2.Set the Address switch on the rear panel of the Zone Expander to "1" if the Zone Expander services zones 9 – 16, set to "2" for zones 17 – 24 and so on until all seven Zone Expanders are utilized (see FIG. 5). Refer to the Zone Expander Addressing section on page 2 for further details.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s). | REV: A | |
|
3/08
©2008 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com