CHANGING THE BLADE DRIVE ASSEMBLY
If your clipper blades no longer cut properly (be sure to try more than one blade, since the blade currently being used may be dull), it could be that your blade drive assembly needs replacement.
To change the blade drive assembly:
1.Remove blade set (Diagram G).
2.Remove drive cap (Diagram H).
DIAGRAM G | DIAGRAM H |
3.Remove blade drive mounting screws (Diagram I).
4.NOTE: Before removing blade drive assembly, note the way it is positioned (this will help you in reassembly). Remove blade drive assembly (Diagram J).
8.Replace drive cap (Diagram H).
9.Replace blade (Diagram M).
DIAGRAM H | DIAGRAM M |
MODEL BGC
Clipper
ANDIS AUTHORIZED
REPAIR
SERVICE STATIONS
BLADE
DRIVE
MOUNTING
SCREWS
DIAGRAM I | DIAGRAM J |
5. Drive bearing should be at its lowest position, if |
not, move it with your finger to lowest position |
FACTORY REPAIR SERVICE
When the blades of your Andis Clipper become dull after repeated use, it is advised to send your blades to an Andis Authorized Service Station mentioned above for resharpening. If you wish your clipper to be serviced as well, they should be carefully packed and mailed either Parcel Post Insured, or U.P.S.
Please refer to the service stations listing
on web site for most up-to-date
Listings !
Thanks
Andis® Model BG
Detachable Blades
are compatible with Oster®
(Diagrams K & L). |
CORRECT | INCORRECT | |
POSITION | ||
POSITION | ||
OF DRIVE | ||
OF | ||
BEARING | ||
DRIVE | ||
| ||
BEARING |
|
DIAGRAM K | DIAGRAM L |
6.Put on new drive assembly, align screw holes and press down (Diagram J).
7.Reassemble blade drive by mounting screws (Diagram I).
LIMITED WARRANTY
This Andis product is warranted against defective material or workmanship for one year from the date of purchase. All implied warranties arising and by virtue of State law shall also be limited to one year. Any Andis product determined to be defective in material or workmanship during the warranty period will be repaired or replaced without cost to consumer for parts and labor. The defective product must be returned with proof of purchase and $6.50 to cover cost of handling, to any Authorized Andis Repair Station or to: Andis, 1800 Renaissance Blvd., Sturtevant, WI 53177 U.S.A. or IN CANADA to: A & AG AGENCIES (CANADA), INC. 10050 Côte de Liesse, Lachine, Québec, H8T 1A3 CANADA. Enclose or attach a letter describing the nature of the problem. Due to foreign matter sometimes found in hair, clipper blades or resharpening of blades are not sub- ject to the one year warranty. The blade set has a 10 Day Limited Warranty. If the blade set fails to cut, it will be resharpened free of charge if returned within 10 days of purchase. Send your blade set postage prepaid with the original purchase receipt to: ANDIS COMPANY, ATTENTION: Service Department, 1800 Renaissance Blvd., Sturtevant, WI 53177 U.S.A. (U.S. & Canada only). Andis will not be liable under this warranty for any defect, failure or malfunction of any of its products cause by normal wear, abuse, misuse, unauthorized adjustments or disassembling. Andis will not be liable for any consequential damages resulting from any defect in material or workmanship of any of its products. Some States do not allow limitations on how long an implied warranty lasts or exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The Warranty gives you specific legal rights, and you may also have other rights which may vary from State to State.
Date
Purchased______________________________________
Model____________________________
KEEP THIS FOR YOUR RECORDS
Form # 22311 Rev. A | ©2001 Andis Company, USA | Printed in U.S.A. |
Models 76, 10 & 111
Congratulations –
You just went First Class
when you bought this Andis Clipper.
Careful workmanship and quality design have been the hallmarks of Andis products since 1922.
