IMPORTANTSAFEGUARDS
When using an electrical appliance, basic precautions should always be followed, including the following:
Read all instructions before using this Andis Trimmer.
DANGER: To reduce the risk of electric shock:
1.Do not reach for an appliance that has fallen into water. Unplug immediately.
2.Do not use while bathing or in a shower.
3.Do not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or drop into water or other liquid.
4.Except when charging, always unplug this appliance from the electric outlet immediately after using.
5.Unplug this appliance before cleaning.
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons:
1.Close supervision is necessary when this appliance is used by, on, or near children or invalids.
2.Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by manu- facturer.
3.Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to a service center for examination and repair.
4.Keep the cord away from heated surfaces.
5.Never drop or insert any object into any opening. Insert only recharging transformer plug into trimmer receptacle.
6.Do not use outdoors or operate when aerosol (spray) products are being used or where oxygen is being administered.
7.Do not use this appliance with a damaged or broken blade or comb as injury to the skin may occur.
8.Always attach plug to appliance first, then to outlet.
To disconnect, turn all controls to “off” then remove plug from outlet.
9. Adjust voltage setting before connecting appliance to outlet.
SAVE THESE INSTRUCTIONS
This product is intended for Professional use.
OPERATING INSTRUCTIONS
CHARGING UNIT
READ THE FOLLOWING BEFORE CHARGING THIS CLIP- PER/TRIMMER
Remove Andis cordless clipper/trimmer and AC adapter from carton. The dual voltage adapter will have to be set manually to the correct voltage before plugging into an electrical outlet. In the U.S.A., adapter must be at 120V setting (as shown in
Fig. 1). Plug adapter into a 120V (or 240V AC outlet, as according to your local power stan- dards). Note that the clipper/trimmer ON/OFF switch must be in the OFF position for the bat- tery to charge. Plug adapter cord directly into the clipper/trimmer (see Fig. 2). The green light on the clipper/trimmer will turn on. The clipper/trimmer is not charged at the factory.
Please recharge clipper /trimmer for 12 hours (overnight) before first use for maximum per- formance.
You can keep the clipper/trimmer plugged into
the adapter when not in use. The adapter will maintain the bat- tery at full charge and the green light will stay on. The unit has a Nickel Metal Hydride battery that cannot be damaged by overcharging. However, we recommend that the adapter be unplugged if the clipper/trimmer won't be used for seven or more days.
PLEASE NOTE: Nickel Metal Hydride batteries have less "Memory Effect" than Nickel Cadmium batteries. Memory Effect is caused by repeated short uses of the clipper/trimmer, followed by charging. The battery never fully discharges and, therefore, "forgets" how much energy it can store. In order to maximize the performance of your Nickel Metal Hydride battery, please follow these steps:
1)Oil blade. Turn clipper/trimmer on and allow it run until the blade slows significantly. It is not necessary to let the blade stop completely.
2)Turn clipper/trimmer off. Charge overnight.
3)Conduct the above exercise every sixty days.
FAILURE TO CHARGE:
1)Make sure voltage is present at the wall outlet (confirm with an appliance you know is working).
2)Check to make sure adapter cord is plugged firmly into trim- mer. Twist the adapter connector slightly to insure good electrical conection. If failure to charge still exists, return trimmer to Andis or an Andis Authorized Service Station listed in this manual for examination and repair or replacement.
ATTENTION: The product you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under vari- ous state and local laws, it may be illegal to dis- pose of this battery into the municipal waste stream. Check with your local solid waste officials (or call 1-800-822-8837) for details in your area for recycling options or proper disposal.
USING TRIMMING COMBS
Your cord/cordless rechargeable trimmer comes complete with six trimming guides. They are 1/2”, 3/8”, 1/4”, 7 day, 5 day and a 3 day for even closer trimming. (See figure 3)
Figure 3
ATTACHING THE TRIMMING COMBS
Slide front of comb over the teeth of the blade. Snap comb down over back of blade. (See figure 4)
Figure 4
BLADES: When trimming is complete, slide on/off switch to off position and remove the trimming comb (if being used). Lightly brush out blades with the blade cleaning brush provided. For best results put a drop of Andis clipper oil on the blade when necessary. Motor bearings are permanently lubricated–do not attempt to oil. Blades should be handled carefully and never bumped or used to cut dirty or abrasive material. Do not use while bathing or in the shower, as damage to batteries and product may
occur.
TRIMMING NECKLINE
Your cord/cordless rechargeable trimmer makes trim-
ming the neckline easier. The results are professional, Fig. 5 too. Simply comb hair into natural position and choose
an attachment comb for the length of cut desired. Trim with the natural grain of the hair. You may wish to use a comb to hold the hair in position until you feel com- fortable using your trimmer. For a closer trim, you may wish to select one of the closer cutting comb attach- ments(Fig. 3).
Fig. 6
TRIMMING BEARD
Always begin with a slightly damp beard for more con- trol when shaping. Comb your beard in the direction the hair grows, to give you an indication of what areas you need to trim. To trim the outer edge of your beard and add definition, hold the trimmer horizontally with
on/off switch facing out. Following the line of your jaw- Fig. 7 bone, cut away longer hairs along the outer edge of
your beard (Figs. 6 & 7). To trim your beard line, hold the trimmer vertically (on/off switch facing you). Start at the trimmed edge of your beard and, with a down- ward motion, trim the area right under your beard line. For added definition of your beard line, use the hori- zontal position to trim any stray hair (Fig. 8).
Fig. 8
