3-16kVA Service Bypass Panels
©2009 APC by Schneider Electric, APC, the APC logo, and
Note: Read the safety information sheet before installation.
Illustrations in this document may differ slightly from the actual hardware.
Attention: This product is for use in a controlled environment. Refer to product specifications for environmental limits.
oWhenever possible, attach one top screw and one bottom screw into a wall stud. If stud mounting is not possible, use an expandable wall anchor. Screws are not included; .25” x 2” lag bolts are recommended.
x4
TOWER OPTION (FOR SMART-UPS RT SETUPS ONLY)
nRemove screw from the top and bottom rear of both the UPS and SBP. Install tie brackets and reattach screws.
USER CONFIGURABLE
Attention: When using an online UPS, put the UPS in automatic bypass mode before rotating the SBP switch.
1.Normal: Power is directed from the utility outlet, through the Bypass Panel and UPS, and to connected equipment. For use during normal UPS operation.
2.Test: Power supplied to the UPS is not output. Use when tests are being conducted on the UPS, and connected equipment is not yet desired.
3.Bypass: Power from the utility outlet is filtered through the Bypass Panel, and to the connected equipment. Use to bypass the UPS, when functioning improperly.
Note: While operating in ‘Test’ or ‘Bypass’ mode, power to the connected equipment is
RACK MOUNTING
n
x4
x2
x8
Front | Rear |
x4
x2
o Unscrew and remove top cover of the p Attach bracket to top of UPS and SBP. UPS.
not conditioned by the UPS. At this time, the “Equipment Protection Policy” is not valid.
IDENTIFYING THE PANEL
Service Bypass Panels will differ. Refer to chart for unit specifications. Note: HW= Hardwire
Service Bypass | Corresponding | Bypass | UPS | UPS | PDU |
Panel | UPS Systems | Input | Input | Output | Panel |
SBP3000RM2U | (2) | ||||
| 3kVA |
|
|
| (6) |
|
|
|
|
|
|
SBP5000RMT2U | 200/208/240V | (2) | |||
|
|
|
| (2) |
oSet SBP in the rack. If hardwiring is required, see Connecting Power section before screwing into the rack.
x4
WALL MOUNTING
n
x8
x2
x1
qReattach top cover of the UPS.
Note: The SBP5000RMI2U, when used in conjunction with an SURT3000XLI or SURT5000XLI UPS in a tower configuration without an external battery pack (SURT192XLBP), is suitable for mounting on concrete or other
| SBP5000RMI2U* |
| 230V |
| C20/HW | C19/HW | C20/HW | (2) C19, |
|
|
|
|
|
|
| (8) C13 |
| ||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| SBP6KRMT2U** |
| 200/208/240V |
|
|
|
| (1) |
| |||
|
| Symmetra |
| HW |
| HW |
| HW |
| (2) |
| |
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| SBP6KRMI2U |
| 230V Symmetra |
| HW |
| HW |
| HW |
| (4) C19 |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| SBP3000 |
| HW |
| HW |
| HW |
| HW |
| ||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| input/output |
|
|
|
|
|
|
|
| |
|
|
| available |
|
|
|
|
|
|
|
| |
| SBP10KRMT4U |
| 200/208/240V |
| HW |
| HW |
| HW |
| (3) |
|
|
|
|
|
|
|
|
|
|
| (3) |
| |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| SBP10KRMI4U |
| 230V |
| HW (3Ph |
| HW (3Ph |
| HW |
| (8) C13, |
|
|
|
|
| or 1Ph) |
| or 1Ph) |
|
|
| (2) C19 |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| SBP16KP |
| HW (3Ph |
| HW (3Ph |
| HW |
| HW |
| ||
|
|
| Symmetra LX | or 1Ph) |
| or 1Ph) |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| ||
| SBP16KRMI4U |
| HW (3Ph |
| HW (3Ph |
| HW |
| (3) 30A HW |
| ||
|
|
| Symmetra LX | or 1Ph) |
| or 1Ph) |
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| ||
| SBP16KRMP4U |
| 200/208/240 |
| HW |
| HW |
| HW |
| (6) |
|
|
|
| Symmetra LX |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 200/208/240 |
| HW |
| HW |
| HW |
| (1) |
| |
|
|
| Symmetra LX |
|
|
|
|
|
|
| (3) |
|
|
|
|
|
|
|
|
|
|
| (1) 100A HW |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
*For loads exceeding 3kVA, hardwiring is necessary.
**For loads exceeding 5kVA, hardwiring is necessary.
