Associated Equipment 9409 Charge Period, Operating Instructions, Maintenance Instructions

NOTE: USE OF AN ADAPTER IS NOT ALLOWED IN CANADA. IF A GROUNDING TYPE RECEPTACLE IS NOT AVAILABLE, DO NOT USE THIS APPLIANCE UNTIL THE PROPER OUTLET IS INSTALLED BY A QUALIFIED ELECTRICIAN.

20.CHARGE PERIOD

The approximate required time to bring a battery to full charge state depends upon the number of ampere-hours (AH) depleted from the battery. AH's are determined by multiplying the number of hours times the number of amps supplied by a battery to a load and normally indicated on the battery. For example, if a load was connected to a battery, which drew 7 amps for a period of 5 hours, the battery will have supplied 35 AH.

The approximate recharge time would then be calculated by dividing the 35 AH depleted from the battery, by the charge rate of the charger. To allow for tapering of the charge rate add 25 percent to the charge time.

OPERATING INSTRUCTIONS

The Model 9409 INTELLAMATIC™ battery charger is designed to charge 12 volt and 6 volt lead-acid batteries of conventional, maintenance- free, or deep cycle construction. This charger will charge both large and small batteries, such as motorcycle and garden tractor batteries. The battery charger will automatically adjust the charging current appropriate to the type of battery.

a.Follow the steps under DC CONNECTION PRECAUTIONS in section 16 when connecting the clamps to the battery. The charger has a "no- spark attachment" feature, however for maximum safety follow the DC CONNECTION PRECAUTIONS.

b.Plug the power cord into a properly grounded electric outlet.

c.The RED indicator lamp will turn on when the battery charger is charging the battery. If the light does not turn on check the output clamps on the battery terminals for proper polarity. The red clamp should be connected to the positive terminal of the battery. If the connections are reversed, unplug the battery charger from electric outlet, and reverse the connections following the DC CONNECTION PRECAUTIONS and plug the power cord into the electric outlet. If the indicator lamp still does not light the charger requires service, unplug the charger's AC power cord and disconnect the charger from the battery.

d.The indicator lamp will begin to blink when the battery is fully charged. The battery charger will stop charging and continuously monitor the battery. The clamps may be removed and the battery is ready for use. ALWAYS DISCONNECT THE CHARGER FROM THE ELECTRICAL

OUTLET WHEN NOT IN USE.

e. If you wish to maintain a battery for an extended period such as winter storage, weekend use only, etc., follow the charging steps above and leave the charger connected to the battery. The charger will automatically turn on when needed to maintain the battery at a full charge. It is recommended that the battery be checked periodically when charging for extended intervals.

The charger may "hum" even when the output is not on because of the AC power used by the transformer. The wattage consumed by the charger when it is plugged in but not charging is small (about 20 watts).

REVERSE CLAMP PROTECTION: If the DC output clamps are connected to the battery backwards, the output of the charger will remain off and the indicator lamp will not light.

SPARK PREVENTION: The output of the INTELLAMATIC™ charger will not activate until there is a voltage across the DC clamps of about 2 volts or higher. [At temperatures below -20 degrees F., charging may not begin unless the battery voltage is above 3 volts.] Additionally the voltage must be present for one second or longer. This prevents an output while the user is attaching the clamps. However if the clamps are removed while the charger is charging, a spark can occur. It is always best to unplug the charger from the electrical outlet BEFORE removing the clamps from the battery.

UPPER BATTERY VOLTAGE LIMITS: The INTELLAMATIC™ charger will not start charging if the battery voltage is above 13.5 volts, this prevents overcharging a battery with a high surface charge. An absolute upper limit of 16 volts has also been included, which applies to 12 volt batteries, and 8 volts for 6 volt batteries.

LOW VOLTAGE CHARGING LIMITS: Charging will not begin unless the voltage across the DC output clamps is above 2 volts. If the charger stops after a few minutes (about 3) unplug the charger from the electric outlet for a few seconds, plug the charger back into the electric outlet to begin the charging cycle again. If the charger again fails to indicate charging after a few minutes unplug the charger from the electric outlet and disconnect the DC clamps from the battery. Have the battery checked at a qualified service center.

TIME LIMIT ON CHARGING: A charging time limit of 17 hours has been set for added safety.

CHARGE COMPLETE SIGNAL: The INTELLAMATIC™ microcomputer checks the battery voltage and monitors the change in voltage with charging time. When the microcomputer determines a full charge the indicator lamp will blink. Output current will be turned off and the lamp will continue blinking until the DC clamps are removed or the charger is unplugged from the electric outlet. It is always best to unplug the charger from the electric outlet BEFORE removing the DC clamps from the battery.

EXTENDED BATTERY MAINTAINER: The INTELLAMATIC™ charger is ideal for maintaining batteries while not in use. When charging is complete, the charger will turn off charging current completely with NO TRICKLE charge that could overcharge a battery. If the battery self discharges below approximately 12.6 volts the charger will activate and recharge the battery, a 6 volt battery will restart at 6.3 volts. It is recommended that the battery be checked periodically when charging over extended intervals.

MAINTENANCE INSTRUCTIONS

This charger requires minimal maintenance. As with any appliance or tool, a few common sense rules will prolong the life of the battery charger. ALWAYS BE SURE THE CHARGER IS UNPLUGGED BEFORE PERFORMING ANY MAINTENANCE OR CLEANING.

1.Store in a clean, dry place

3