The pattern control knob on the CTM-1500VPhas a center detented cardioid position. This allows the user to quickly and consistently lock the mic in a cardioid pattern. By turn- ing the knob clockwise from the center, the pattern varies continuously from cardioid, to subcardioid, through omni- directional. By turning the knob counterclockwise from the center, the pattern varies continuously from cardioid, to hypercardioid through bidirectional (Fig.8). This allows the user to adjust to the optimal pattern needed for almost any recording or live situation.

Getting Started

The high gain and wide bandwidth of the CTM-1500VPmicrophone will easily overload the inputs of many professional mixing consoles if adequate precautions are not taken. This is especially true if the microphone is going to be used on percussion or amplified electronic instruments. If you have never used this microphone before, we strongly recommend that you initially reduce the system gain by doing one or more of the following:

•Enable the pad switch on the input of your mixing console.

•Start with the input trim control on your mixing console turned down to a low level.

•Enable the -20 dB pad switch on the CTM-1500VPmicrophone.

•The CTM-1500VPrequires a 24-52V phantom power supply, delivering at least 8mA for proper operation.

Specifications*

Type:

Side address, external bias condenser

Frequency Response:

10Hz-20kHz

Polar Pattern:

Variable

Impedance:

200ohms

Sensitivity:

-36 dBV (16mV) @ 1Pa

Equivalent Noise Level:

11dB-A

Maximum SPL:

143dB SPL (with pad)

Total Harmonic Distortion: Less than 0.15%

Powering:

Minimum Requirements are 24-52V phantom power capable of delivering at least 8 mA.

Connector:

Three pin male XLR type.

Finish:

Durable charcoal gray urethane. Black urethane front & rear screen.

Dimensions:

2.25" (57.2 mm) Dia., x 7.00" (177.8 mm) High

Net Weight:

17.8 oz. (506 grams)

Architect's and Engineers' Specification

The microphone shall be a dual diaphragm externally biased condenser microphone. The frequency response shall be 10Hz - 20KHz. The microphone shall have a continuously variable polar pattern.

SPECIFICATIONS FOR CTM-1500VP

 

cardioid

fig. 8

omni

 

 

 

 

*Due to our continuous efforts to improve our products and promote the development of standards, specifications are subject to change without notice.

The sensitivity of the CTM-1500VPshall be -36dBV (16mV) @ 1Pa. The microphone shall have a professional 3 pin XLR type output connector. The microphone shall have a switch selectable 100Hz high pass filter with a 6dB per octave slope when enabled. The microphone shall have a switch selectable 20dB non-capacitive pad. The microphone will operate from standard 48V phantom power with a current consumption of 8mA.

The dimensions of the microphone shall be 6 11/16" tall, 2" wide, and 15/16" high. The weight of the microphone shall be 17.8 oz (506 grams) not including the shockmount. The microphone will have a durable urethane painted finish. The microphone will supplied with a shockmount.

The microphone shall be an ASTATIC CTM-1500VP.

TWO-YEAR LIMITED WARRANTY

ASTATIC Microphones are warrantied for two years to the original purchaser from the date of purchase by Omnitronics, LLC to be free from defects in material and workmanship. In event of such defect, product will be repaired or replaced at Omnitronics, LLC discretion with a new unit of equal or superior value. This will be at no charge if delivered prepaid to Omnitronics, LLC, together with the proof of purchase and a Return Authorization number. The unit will be returned promptly prepaid. Warranty excludes exterior finish, appearance items, or malfunction due to abuse or operation under other than specified conditions. Consequential or incidental damages are excluded.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusions and limitations maynotapplytoyou.

Note: No other warranty, written or oral is authorized by Omnitronics, LLC.

SHIPPING INSTRUCTIONS

Pleasecallourcustomer service department at 440-593-1111 for a pre-approved returnauthorizationnumber and carefullyrepack the unit and return it to: Omnitronics, LLC, 341 Harbor St., Conneaut, OH 44030

ALL RETURNS MUST HAVE A PRE-APPROVED RETURN AUTHORIZATION NUMBER OR IT WILL BE REFUSED.

If outside the United States, contact your dealer or distributor for warranty details.

46873-64-00 / Rev.0 / 2/16/05 / S.L.W.

Page 1 Page 2
Page 2
Image 2
Astatic CTM-1500VP manual Getting Started, Specifications
Page 1 Page 2

CTM-1500VP specifications

The Astatic CTM-1500VP is a high-performance professional dynamic microphone renowned for its versatility and exceptional audio quality. Designed primarily for vocal applications, this microphone is perfect for both live performances and studio recording, making it a favorite among musicians, vocalists, and sound engineers alike.

One of the standout features of the CTM-1500VP is its variable polar pattern. This adjustable pattern allows users to switch between cardioid, supercardioid, and omnidirectional modes, providing flexibility to adapt to different sound environments and performance needs. Whether you want to isolate vocals in a noisy setting or capture ambient sounds, the CTM-1500VP delivers excellent results.

The microphone operates using a dynamic design, which means it requires no external power source, making it highly reliable and easy to use in a variety of settings. Its robust construction ensures durability, enabling it to withstand the rigors of touring and daily use. The rugged metal housing and reinforced grille protect the internal components from physical damage, while the lightweight design facilitates easy handling.

Another notable characteristic of the CTM-1500VP is its wide frequency response. It captures a broad range of sound frequencies, from deep bass to soaring highs, ensuring that every nuance of the performance is delivered with clarity and detail. This frequency response is complemented by its high output level, which guarantees strong signal performance and minimizes the risk of distortion even at high volumes.

In addition to its acoustic advantages, the CTM-1500VP features built-in shock mount technology that significantly reduces handling noise and vibrations. This feature is particularly beneficial in live music settings, where overhead noise can detract from the overall sound quality.

The microphone also comes equipped with a pop filter, which helps minimize plosive sounds, ensuring that recordings are clean and professional. This combination of technologies makes the Astatic CTM-1500VP an ideal choice for a variety of applications, including live sound reinforcement, studio recording, and broadcast.

In summary, the Astatic CTM-1500VP is a versatile, durable, and high-quality microphone that caters to the needs of professionals in the audio industry. Its variable polar patterns, wide frequency response, and built-in noise reduction technologies make it an essential tool for anyone looking to capture high-fidelity sound in any environment. With its blend of functionality and performance, the CTM-1500VP stands out as a leading choice among dynamic microphones.
Top Page Image Contents