Manuals / Brands / Computer Equipment / Computer Hardware / Asus / Computer Equipment / Computer Hardware

Asus A7N266-E ASUS A7N266-EUser’s Manual, These are not jumpers, do not place jumper caps over these connectors

1 100

Download 100 pages, 2.89 Mb

3.HARDWARE SETUP

12)CPU Fan, North Bridge Fan, and Chassis Fan Connectors (CPU, NB, CHA_FAN)

The three fan connectors support cooling fans of 350mA (4.2 Watts) or less. Orient the fans so that the heat sink fins allow airflow to go across the onboard heat sinks instead of the expansion slots. The fan wiring and plug may vary. Connect the fan cable to the connector making sure that the black wire matches the ground pin. NOTE: Use the “Rotation” signal only with a specially designed fan with a rotation signal. Monitor Rotations Per Minute (RPM) using ASUS PC Probe (see section 6. SOFTWARE REFERENCE).

WARNING! Make sure to connect the fan cables to the fan connectors. Lack of sufficient airflow within the system could cause damage to the motherboard.

These are not jumpers, do not place jumper caps over these connectors!

A7N266-E

CHA_FAN GND

+12V

Rotation

CPU_FAN GND

+12V

	Rotation
NB_FAN	GND
NB_FAN	+12V
	Rotation

A7N266-E 12-Volt Cooling Fan Power

Connectors

3. H/W SETUP

ASUS A7N266-E User’s Manual

37

Contents

JumperFree™ DDR DRAM 266MHz FSB Product Name: ASUS A7N266-E Manual Revision: 1.00 E901 Release Date: November ASUSTeK COMPUTER INC. (Asia-Pacific) Marketing Technical Support ASUS COMPUTER INTERNATIONAL (America) ASUS COMPUTER GmbH (Europe) 2.1.4 Performance and Intelligence 3.7.1 Installing an Expansion Card 3.7.2 Assigning IRQs for Expansion Cards 3.7.3 Accelerated Graphics Port (AGP) Pro Slot 3.7.4 Advanced Communications Riser (Slot) 4.3.1 Primary & Secondary Master/Slave A7N266-ESeries Motherboard Support CD 5.3.3 Manual Installation of Drivers for Windows 98 7.2.3 Hardware Installation Procedure 7.2.4 Software Setup in Windows 98 Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver •Consult the dealer or an experienced radio/TV technician for help 1.1How This Manual Is Organized 1.2 Item Checklist 2.1ASUS A7N266-EMotherboard 2.1.1 Core Specifications 2.1.2Connections 2.1.3 Special Features 2.1.4Performance and Intelligence Two Onboard LEDs: green red warning Concurrent PCI: 2.2Motherboard Components 2.2.1Component Locations 3.1Motherboard Layout 3.2Layout Contents 3.3 Hardware Setup Procedure 3.4Motherboard Settings 2)Jumperfree Setting (JEN) 3)CPU:DRAM Frequency Setting (BSEL0, BSEL1) Note CPU BSEL0 4)Voltage Regulator Output Setting (VID1, VID2, VID3, VID4) 5)DDR Voltage Setting (VDDR) Setting VDDR [3-4] 6)USB Device Wake-up(USB01PWR / USB23PWR / USB45PWR) 7)Clear RTC RAM (2-pinCLR_RTC) 1.Turn OFF the computer and unplug the power cord 2.Remove the battery 4.Re-installthe battery 3.5System Memory 3.5.1 DDR DIMM Support 3.5.2Memory Installation 3.5.4 General DIMM Memo 3.6Central Processing Unit (CPU) 3.7Expansion Cards 3.7.1 Installing an Expansion Card 3.7.2Assigning IRQs for Expansion Cards Standard Interrupt Assignments Interrupt Request Table for this Motherboard 3.7.3Accelerated Graphics Port (AGP) Pro Slot 3.7.4Advanced Communications Riser (Slot) ACR-A6CHLayout ACR-A6CHHardware Installation Procedure 3.8Connectors 3.8.1 External Connectors 4)Parallel Port (Burgundy 25-pinPRINTER) Onboard Parallel Port 4.4.2 I/O Device Configuration) NOTE: Serial printers must be connected to the serial port 5)Fast Ethernet Port (RJ-45)(Optional) Serial Port Connectors (Teal/Turquoise 9-pin COM1 pin COM2) Onboard Serial Port 1/2 8)Game/MIDI Ports (Gold 15-pinGAME) (Optional) 9)IDE Activity LED (2-pinIDELED) 10)Floppy Disk Drive Connector (34-1pin FLOPPY) 11)Primary (Blue) / Secondary IDE Connectors (40-1pin IDE1/IDE2) NOTES: 2.The hole near the blue connector on the UltraDMA/100/66 cable is intentional TIP: You may configure two hard disks to be both Masters with two ribbon TIP: 12)CPU Fan, North Bridge Fan, and Chassis Fan Connectors (CPU, NB, CHA_FAN) These are not jumpers, do not place jumper caps over these connectors 13)Infrared Connector (10-1pin IrDA) 14)Power Supply Connectors (20-pinblock ATXPWR) IMPORTANT: Make sure that the ATX 12V power supply (minimum 15)Chassis Open Alarm Lead (4-pinCHASSIS) 16)USB Headers (10-1pin USB2_3, USB4_5) 17)Power Supply Thermal Sensor Connector (2-pinJTPWR) 18)SMBus Connector (5-1pin SMB) 19)System Power LED Lead (3-1pin PWR.LED) 20)Keyboard Lock Switch Lead (2-pinKEYLOCK) 21)System Warning Speaker Lead (4-pinSPEAKER) 22)System Message LED Lead (2-pinLED) 23)System Management Interrupt Lead (2-pinSMI) 3.9Starting Up the First Time Award BIOS Beep Codes 4. BIOS SETUP Powering Off your computer: Start Shut Down Shut down the computer 4.1Managing and Updating Your BIOS 4.1.1 Upon First Use of the Computer System 1. Save Current BIOS to File Save Current BIOS To File A:\XXX-XX.XXX SETUP BIOS 4.1.2Updating BIOS Procedures Page 4.2BIOS Setup Program 4.2.1BIOS Menu Bar 4.2.2 Legend Bar General Help Saving Changes and Exiting the Setup Program Scroll Bar Sub-Menu 4.3Main Menu 4.3.1Primary & Secondary Master/Slave [User Type HDD] Translation Method [LBA] Cylinders Type Translation Method CHS Capacity Maximum LBA Capacity Multi-SectorTransfers [Maximum] SMART Monitoring [Disabled] PIO Mode [4] 4.3.2Keyboard Features Language [English] This field displays the BIOS language version A Note about Passwords Forgot the Password To erase the RTC RAM: 4.4Advanced Menu CPU/Memory Frequency Ratio [Auto] CPU/PCI Frequency (MHz) CPU Level 1 Cache, CPU Level 2 Cache [Enabled] CPU Level 2 Cache ECC Check [Enabled] BIOS Update [Enabled] Summary of Warning Messages 4.4.1Chip Configuration Internal Graphic Over-clocking[Disable] VGA LCD TV Display Type [Auto] Video Memory Cache Mode [UC] Onboard VGA BIOS Update [Enabled] MCP IDE Controller [Both] 4.4.2I/O Device Configuration Parallel Port Mode [ECP+EPP] ECP DMA Select [3] ECP Parallel Port Mode Onboard Game Port [200H-207H] 4.4.3PCI Configuration PCI DMA Resource Exclusion PCI UMB Resource Exclusion 4.4.4Shadow Configuration 4.5Power Menu 4.5.1 Power Up Control 4.5.2Hardware Monitor 4.6Boot Menu Boot Sequence Boot Virus Detection [Enabled] Quick Power On Self Test [Enabled] Boot Up Floppy Seek [Enabled] Interrupt Mode [APIC] Configuration options: [APIC] [PIC] 4.7Exit Menu Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes 5.1Install Operating System 5.2 Start Windows 5.3A7N266-ESeries Motherboard Support CD 5.3.1 Installation Menu 5.3.2 Installation Procedure 5.3.3Manual Installation of Drivers for Windows ITEM 3: PCI Standard Ram Controller 1.Go to the Device Manager 2.Select PCI standard RAM Controller in “System Devices” 5.Select “update driver” ITEM 4: ACR-A6CH-AudioCard drivers: 6.1ASUS Live Update 6.2ASUS PC Probe 6.2.1 Starting ASUS PC Probe 6.2.2Using ASUS PC Probe Settings CPU Cooling System Setup History Information Hard Drives Memory Device Summary DMI Explorer Utility Execute Program 6.2.3ASUS PC Probe Task Bar Icon 6.33Deep Color Tuner 6.3.13Deep Color Tuning 6.3.2The 3Deep Control Panel 6.4CyberLink PowerPlayer SE 6.4.1 Starting CyberLink PowerPlayer SE 6.4.2 CyberLink PowerPlayer Control Panel 6.5CyberLink VideoLive Mail 6.5.1Starting VideoLive Mail 6.5.2CyberLink VideoLive Mail User Interface 7.1 Glossary APPENDIX Page Page 7.1 Modem Riser 7.2.1 56K Software Modem 7.2.2 Primary/Seconday MR Layout of Primary 7.2.3Hardware Installation Procedure 7.2.4Software Setup in Windows INDEX