Asus P/I-XP6NP5 54

(This page was intentionally left blank)

48	ASUS P/I-XP6NP5 User's Manual

Contents

Page USER'S NOTICE © Copyright 1997 ASUSTeK COMPUTER INC. All rights reserved Product Name: ASUS P/I-XP6NP5 Manual Revision: ASUSTeK COMPUTER INC Marketing Info: Technical Support: ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS I. INTRODUCTION II. FEATURES III. INSTALLATION IV. BIOS SOFTWARE V. DESKTOP MANAGEMENT VI. ASUS PCI-SC200SCSI Card VII. ASUS I-A16CAudio Card VIII. DOS 3.1 & Windows 3.1x Audio Software IX. Windows 95 Audio Software FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this manual is organized Item Checklist Features of the ASUS Motherboard Parts of the ASUS Motherboard Map of the ASUS Motherboard Jumpers Expansion Slots Connectors INSTALLATION (Map of Board) Installation Steps 1. Jumpers III.INSTALLATION 1.Onboard Multi-I/OSelection (JP14) Multi-I/OJP14 2.Flash ROM Boot Block Programming (JP17) Programming 3.Real Time Clock (RTC) RAM (JP16) RTC RAM JP16 Operation (Default) 4.Battery Test Lead (JP7) 5.CPU External Clock (BUS) Frequency Selection (JP8, JP9) 6.CPU to BUS Frequency Ratio (JP10, JP11, JP12, JP13) Set the jumpers by the Internal speed of the Intel CPU as follows: 7.Voltage Regulator Output Selection (JP1, 2, 3, 4) 8. 3.3Volt Power Source (JP6) 3.3V Power Source Onboard Regulator ATX Power Supply 2.System Memory (DRAM & SRAM) DRAM Memory Installation Procedures: Page 3.Central Processing Unit (CPU) 4.Expansion Cards Expansion Card Installation Procedure: Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards Page 5.External Connectors 5.ATX Power Connector (20-pinblock) 6.Floppy Drive Connector (34-pinblock ) 7.Primary / Secondary IDE connectors (Two 40-pinBlock) 8.IDE Activity LED (JP15) 9.System Power LED (TB LED) 10.SMI Suspend Switch Lead (SMI) 11.ATX Power Switch (PWR SW.) 12.Reset Switch Lead (RESET) 13.Keyboard Lock Switch Lead & System Power LED (KEYLOCK) 14.Speaker Connector (SPEAKER) This 4-pinconnector connects to the case-mountedspeaker 15.CPU Cooling Fan Connector (FAN) These are not jumpers, do not place jumper caps over these pins 16.IrDA-CompliantInfrared Module Connector (IR) Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu Advanced Features Menu Updating your Motherboard's BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: For IDE hard disk drive setup, you can: •Use the Auto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option CYLS HEAD Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) EGA/VGA, Mono (for Hercules or MDA), CGA 40, and CGA BIOS Features Setup Details of BIOS Features Setup CPU Fast String (Enabled) Leave on default setting of Enabled for best performance Deturbo Mode (Disabled) Enabled Quick Power On Self Test (Enabled) Typematic Rate Setting (Disabled) Typematic Rate (Chars/Sec) 8, 10, 12, 15, 20, 24 Typematic Delay (Msec) (250ms) OS/2 Onboard Memory > 64M (Disabled) Chipset Features Setup Details of Chipset Features Setup (Chipset Read-Around-Write Enabled 16-bitI/O Recovery Time Timing for 16-bitISA cards (leave on default setting of 1 BUSCLK) Onboard FDC Swap A: B: (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Power Management Setup Details of Power Management Setup Video Off Method (V/H SYNC + Blank) Suspend Switch (Enabled) Doze Speed, Stdby Speed PM Timers HDD Power Down PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) NCR SCSI BIOS (Auto) USB Function (Disabled) Passive Release (Enabled) Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save and Exit Setup Exit Without Saving Page Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes: Save MIFD Load MIFD Load BIOS Defaults Page NCR SCSI BIOS and Drivers The ASUS PCI-SC200SCSI Interface Card Setting Up the ASUS PCI-SC200 Setting the INT Assignment Terminator Settings SCSI ID Numbers ASUS I-A16CAudio Features Unpacking and Handling Precautions Layout and Connectors Connectors CD-AudioConnector Pin Definitions