Asus P2-99 92

(This page was intentionally left blank.)

92	ASUS P2-99 User’s Manual

Contents

Page USER'S NOTICE Product Name: ASUS P2-99 Manual Revision: 1.13 E408 Marketing Technical Support CONTENTS Page FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual Is Organized Item Checklist Features of the ASUS P2-99Motherboard II.FEATURES Wake-On-LAN •IrDA: Supports an optional infrared port module for a wireless interface Special Features: Enhanced ACPI and Intelligent Features (only with optional hardware monitor): Auto Fan Off: even in sleep mode and system noise The ASUS P2-99Motherboard Motherboard Parts II. FEA TURES Layout of the ASUS P2-99Motherboard Motherboard Settings Expansion Slots/Sockets Hardware Monitor (optional) Connectors Layout Contents Hardware Setup Steps 1. Motherboard Settings III.HARDWARE SETUP 2.Keyboard Power Up Setting (KBPWR) 3.I/O Voltage Setting (VIO) Motherboard Settings Jumpers 4.Voltage Regulator Output Setting (VCORE) This jumper sets the core voltage supplied to the microprocessor Test 5.CPU Bus Frequency Selection (FS0, FS1, FS2, FS3) 6.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Set the jumpers by the Internal speed of your processor as follows: NOTES: H/W SETUP 2.System Memory (DIMM) DIMM Memory Installation Procedures Page 3.Central Processing Unit (CPU) Universal Retention Mechanism Heatsinks Installing the Processor 1. Unlock the URM’s Folding Support Arms: The folding support arms of the URM are locked when shipped To unlock the support arms, simply flip them up to an upright position 3.Insert the SECC/SECC2/SEPP SECC with Pentium II only: 4.Secure the SECC/SECC2/SEPP ASUS Smart Thermal Solutions Recommended Heatsinks for Slot 1 Processors 4.Expansion Cards Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor Accelerated Graphics Port (AGP) 5.External Connectors 3.Parallel Port Connector (25-pinfemale) Chipset Features Setup NOTE 4.Serial Port COM1 and COM2 Connectors (Two 9-pinmale) 6.Primary / Secondary IDE Connectors (Two 40-1pinIDE) 7.Floppy Disk Drive Connector (34-1pinFLOPPY) 8.IDE Device Activity LED (2-pinIDELED) 9.Wake-On-RingConnector (2-pinWOR) do not place jumper caps over these pins 11.Wake-On-LANConnector (3-pinWOL_CON) 12.IrDA-CompliantInfrared Module Connector (5-pinIR) 13.SB-Link™Connector (6-1pin SBLINK) 14.SMBus Connector (5-1pin SMB) 15.ATX Power Supply Connector (20-pinATXPWR) 16.Chassis Intrusion Alarm Lead (optional) (4-1pin CHASIS) 17.System Power LED Lead (3-1pin PWR.LED) 18.Keyboard Lock Switch Lead (2-pinKEYLOCK) 20.System Message LED Lead (2-pinMSG.LED) 21.System Management Interrupt Lead (2-pinSMI) 22.ATX Power Switch / Soft-OffSwitch Lead (2-pinPWR.SW) Power Connection Procedures Flash Memory Writer Utility 2. Update BIOS Including Boot Block and ESCD Flash Memory Writer Managing and Updating Your Motherboard’s BIOS Upon First Use of the Computer System 2.Copy AFLASH.EXE to the just created boot disk Run AFLASH.EXE from this new disk and select option 1. Save Current BIOS to File 6. BIOS Setup Load Defaults Details of Standard CMOS Setup Time (Hour: (00 to 23), Minute: (00 to 59), Second: (00 to 59) Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup Auto detection of hard disks on bootup Drive A / Drive B Floppy 3 Mode Support Drive A, Drive B, Both Disabled Details of BIOS Features Setup Features BIOS Processor Serial Number (Enabled) CPU Level 1 Cache / CPU Level 2 Cache (Enabled) CPU Level 2 Cache ECC Check (Disabled) This function controls the ECC check capability in the CPU level 2 cache PS/2 Mouse Function Control (Auto) OS/2 Onboard Memory > 64M (Disabled) PCI/VGA Palette Snoop (Disabled) Video ROM BIOS Shadow (Enabled) C8000-CBFFFto DC000-DFFFF(Disabled) Details of Chipset Features Setup Timing for 16-bitand 8-bitISA cards, respectively. Leave on default setting Graphics Aperture Size (64MB) Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Onboard Parallel Port (378H/IRQ7) Parallel Port Mode (ECP+EPP) ECP DMA Select (3) ECP ECP+EPP Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Wake On LAN (Disabled) IMPORTANT: Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) Symbios SCSI BIOS (Auto) USB IRQ (Enabled) VGA BIOS Sequence (PCI/AGP) Load BIOS Defaults Load Setup Defaults Defaults Load Supervisor Password and User Password Forgot the password Passwords IVHard IDE HDD Auto Detection Hard Disk Detect Save & Exit Setup Exit Without Saving Page SOFTWARE CONTENTS V. SOFTWARE SETUP VI. SOFTWARE REFERENCE Installing ASUS PC Probe (optional) LDCM Local Setup (optional) S/W SETUP LDCM Administrator Setup (optional) Uninstalling Programs Installing Adobe Acrobat Reader (optional) ASUS PC Probe (optional) Fan Rotation Status PC Temperature Status PC Voltage Status PC Status Summary PC Probe System Info PC Probe Settings PC Probe Task Bar Icon Intel LANDesk Client Manager (optional) Toolbar Descriptions Using the Select Computer Dialog Box To select a computer 1.From the main Client Manager window, click File | Select Computer 2.In the Select Computer dialog box, click the computer you want to view 3.Click the Select button To discover new computers Displaying the Properties of a Client Computer Understanding the Computer Status Icons Unavailable Wakeable Wake Pending Normal Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility Starting the ASUS DMI Configuration Utility Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults VII. APPENDIX ASUS CIDB Chassis Intrusion Sensor Module VII. APPENDIX Using the ASUS CIDB 1.You must have an ASUS motherboard with a chassis connector ASUS CIDB Additional Considerations The ASUS S370 CPU Card Setting up the ASUS S370 ASUS S370 Jumper Settings not ASUS PCI-L101Fast Ethernet Card Features •Intel 82558 Ethernet LAN Controller (Fully integrated 10BASE-T/100BASE-TX) •Wake-On-LANRemote Control Function Supported •PCI Bus Master Complies to PCI Local Bus Rev. 2.1 specifications •Consists of MAC & PHY (10/100Mbps) interfaces Glossary Byte (Binary Term) COM Port CPU (Central Processing Unit) Device Driver DOS (Disk Operating System) PCI Bus (Peripheral Component Interconnect Local Bus) Peripherals POST (Power On Self Test) PS/2 Port RAID (Redundant Array of Independent Disks) USB (Universal Serial Bus)