Manuals / Brands / Kitchen Appliance / Water Dispenser / Asus / Kitchen Appliance / Water Dispenser

Asus P2L97 Jumper Settings, ASUS P2L97 User’s Manual, 1.Real Time Clock (RTC) RAM (CLRTC)

1 64

Download 64 pages, 819.54 Kb

III. INSTALLATION

Jumper Settings

1.Real Time Clock (RTC) RAM (CLRTC)

The CMOS RAM is powered by the onboard button cell battery. To clear the RTC data: (1) Turn off your computer and unplug your AC power, (2) Short the two points (Labeled: CLRTC), (3) Turn on your computer, (4) Hold down <Delete> during bootup and enter BIOS setup to re-enter user preferences.

Short small solder points to clear

CLRTC

Clear RTC RAM

INSTALLATION	(Jumpers)
III.

ASUS P2L97 User’s Manual

Contents

Page USER'S NOTICE Copyright © 1997 ASUSTeK COMPUTER INC. All Rights Reserved Product Name: ASUS P2L97 Manual Revision: ASUSTeK COMPUTER INC Marketing Info Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS I. INTRODUCTION II. FEATURES III. INSTALLATION IV. BIOS SOFTWARE V. DESKTOP MANAGEMENT VI. ASUS PCI SCSI Cards FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features of the ASUS P2L97 Motherboard The ASUS P2L97 Motherboard Layout of the ASUS P2L97 Motherboard Jumpers Expansion Slots/Sockets Connectors III. INSTALLATION (Board Layout) (Board Layout) Installation Steps 1. Jumpers Jumper Settings III.INSTALLATION 2.CPU Bus Frequency (FS0, FS1, FS2) 3.CPU Core:BUS Frequency Multiple (BF0, BF1, BF2, BF3) Internal External Page Page 2.System Memory (DIMM) DIMM Memory Installation Procedures: 3.Central Processing Unit (CPU) Pentium II Processor The Motherboard As Shipped Installing the Pentium II Processor: Mount the Pentium II Retention Mechanism: TIP: Insert the SEC Cartridge: Secure the SEC Cartridge: AAVID Heatsink Elan Vital Heatsink 4.Expansion Cards Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards ISA Cards and Hardware Monitor 5.External Connectors 3.Parallel Printer Connector (25-pinFemale) NOTE 4.Serial Port COM1 and COM2 Connectors (Two 9-pinMale) 5.Floppy Disk Drive Connector (34-1pinFLOPPY) III. INSTALLATION 7.Primary / Secondary IDE connectors (Two 40-1pinIDE) 8.IDE activity LED (2-pinIDE_LED) 9.Chassis , CPU , & Power Supply Fan Connectors (3-pinFANPWR) do not place jumper caps over these pins (Connectors) 10.IrDA / Fast IR-Compliantinfrared module connector (5-pinIR) 11.ATX Power Supply Connector (20-pinATXPWR) 12.Wake on LAN (3-pinWOL) 13.Message LED Lead (MSG LED) 14.SMI Suspend Switch Lead (SMI) 15.ATX Power Switch / Soft Power Switch (PWR SW) 16.Reset Switch Lead (RESET) 17.System Power LED (PWR LED) Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu Advanced Features Menu Managing and Updating Your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: Time Hard Disks For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option Auto detection of hard disks on bootup Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A, Drive B, Both, and Disabled Video (EGA/VGA) BIOS Features Setup Details of BIOS Features Setup (BIOS CPU Level 1 Cache / CPU Level 2 Cache (Enabled) BIOS Update (Enabled) CPU Fast String (Enabled) Leave on default setting of Enabled for best performance Security Option (System) Supervisor Password User Password System Setup Chipset Features Setup Details of Chipset Features Setup Video Memory Cache Mode (UC) USWC PCI 2.1 Support (Enabled) Enable Disable Onboard FDC Swap A & B (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are and for the onboard serial connector Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) DPMS OFF DPMS Reduce ON Blank Screen V/H SYNC+Blank, DPMS Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Disabled Automatic Power Up (Disabled) Fan Monitor (xxxxRPM) PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) SYMBIOS SCSI BIOS (Auto) Auto BIOS Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults Symbios SCSI BIOS and Drivers Setting Up the ASUS PCI-SC200& PCI-SC860 Setting the INT Assignment for the ASUS PCI-SC200 Terminator Requirements for SCSI Devices Terminator Settings for the ASUS PCI-SC860 Terminator Settings for the ASUS PCI-SC200 SCSI ID Numbers for SCSI Devices SCSI ID Priority