Asus SP97, SP97-V (This page was left intentionally left blank)

III. INSTALLATION

(This page was left intentionally left blank)

INSTALLATION .III Memory) (System

22	ASUS SP97 / SP97-V User’s Manual

Contents

Page USER’S NOTICE Product Name: ASUS SP97 / SP97-V Manual Revision: Release Date: ASUSTeK COMPUTER INC Marketing Info Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS Page FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features of the ASUS SP97 Motherboard Introduction to ASUS SP97 Series of Motherboards (This page was intentionally left blank) The ASUS SP97 Motherboard ASUS SP97 Motherboard Layout Jumpers Expansion Slots Connectors Installation Steps 1. Jumpers Jumper Settings Compatible Cyrix CPU Identification III.INSTALLATION 3.CPU External Frequency (BUS) Selection (FS0, FS1, FS2, FS3) 4.CPU to BUS Frequency Ratio (BF0, BF1, BF2) Page 6.VGA Selection (VGA_INT) (with onboard VGA version only) 2.System Memory (SIMM) SIMM Installation (This page was left intentionally left blank) 3.Central Processing Unit (CPU) 4.Expansion Cards Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards 5.External Connectors 3.Parallel Port Connector (PRINTER, 26-1pin block) 4.Serial Port Connectors (COM1/COM2, two 10-1pin blocks) III. INSTALLATION 5. Power Supply, Chassis Fan Connectors (PWR_, CPU_, CHA_FAN, 3 pins) This connector supports a 3-pin Positive 7.Message LED Lead (MSG.LED, 2 pins) 8.SMI Suspend Switch Lead (SMI, 2 pins) 9.ATX Power Switch/Soft Power Switch Lead (PWR.SW, 2 pins) 10.Reset Switch Lead (RESET, 2 pins) 11.System Power LED (PWR.LED, 3 pins) 15.Second IrDA-CompliantInfrared Connector (IR, 5-pinblock) UART2 Use Infra- red Chipset Features Setup 16.AT Power Supply Connector (POWER, 12-pinblock) 17. ATX Power Supply Connector (ATXPWR, 20-pinblock) 18.IDE Activity LED (IDELED, 2 pins) 20.Video Feature Connector (26 pins) (with onboard VGA version only) Page Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu Advanced Feature Menu Managing and Updating Your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: Autodetection of Hard Disks on Bootup NOTE: SETUP Defaults are noted in parenthesis next to each function heading Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A BIOS Features Setup Details of BIOS Features Setup (BIOS Boot Sequence (C,A) Boot Up Floppy Seek (Disabled) When enabled, the BIOS will seek drive A one time Floppy Disk Access Control (R/W) Chipset Features Setup Details of Chipset Features Setup (Chipset Linear Mode SRAM Support (Leave on default setting of Disabled) WARNING: 16-bit ISA Wait State Onboard FDC Swap A: B: (No Swap) Onboard Serial Port 1 (3F8H/IRQ4) Settings are (default) and Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) PM Timers HDD Power Down (Disable) Doze Mode, Standby Mode, Suspend Mode (Disable) Power Up Control PNP and PCI Setup Details of PNP and PCI Setup IRQ xx Used By ISA (No/ICU) No/ICU IRQ10 Used By ISA DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save and Exit Setup Exit Without Saving Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults Symbios SCSI BIOS and Drivers Setting Up the ASUS PCI-SC200& PCI-SC860 Setting the INT Assignment for the ASUS PCI-SC200 Terminator Requirements for SCSI Devices Terminator Settings for the ASUS PCI-SC860 Terminator Settings for the ASUS PCI-SC200 SCSI ID Numbers for SCSI Devices SCSI ID Priority ASUS I-A16CAudio Features Unpacking and Handling Precautions Layout and Connectors Connectors CD-AudioConnector Pin Definitions Page VIDEO SOFTWARE USER’S MANUAL VIII. DOS UTILITY IX. SOFTWARE DRIVERS ASUS SP97-VUser’s Manual DOS Utility 1. SVGAUTL.EXE 1.1 General Description 1.2 How to Use 1.3 What the Parameters Stand for A1. Video Modes NOTE: i - interlaced mode n - noninterlaced mode A1.2 Enhanced Video Modes Page Page Software Drivers 1. Windows 1.0 Version Notes 1.1 Driver Files 1.2 Installation 1.2.3 Power Saving Setup in Windows 2.In “Power Saver” Screen, choose which options you would like to use 1.2.4 Zoom_Key Setup The operation principles of zoom-inand zoom-outare as follow: (1)The resolution change sequence for zoom-inis 1.3 Video Operations MMPLAY.EXE Button Description Page 2. Windows 2.0 Version Note 2.1 Driver Files 2.2 Installation 2.3 Using “Display Modes” 2.4 Utilities 3. Windows NT 3.5 & 4. Windows NT 5. Autodesk ADI 4.2 -ProtectedMode 5.0 General Description 5.1 AutoCAD R11 Setup 5.2 AutoCAD R1.2 Setup 5.3 AutoShade R2.0 Setup 5.4 3D Studio Version 3.0 Setup 12.After detail configuration, you will enter the 3DS main display screen and you may begin your 3D Studio work in the environment you make before \3DS3\3DS <Enter (3D Studio) 6. OS/2 6.0 Driver Notes 6.1 Driver Files 6.2 Installation 7. OS/2 V3.0 (Warp) 7.0 Driver & OS/2 Version Notes 7.1 Driver Files 7.2 Installation 8. Double Bytes OS/2 Warp 8.0 Driver & OS/2 Version Notes 8.1 Driver Files 8.2 Installation