Asus TXP4-X ASUS TXP4-XMotherboard Layout, III. INSTALLATION

III. INSTALLATION

ASUS TXP4-X Motherboard Layout

INSTALLATION .III Layout) (Motherboard

PS/2

USB

1COM

PortParallel

2COM

Keyboard BIOS

T: Mouse

B: Keyboard

T: USB 1

module)pin-72bit,-(324SocketSIMM

module)pin-72bit,-(323SocketSIMM

module)pin-72bit,-(322SocketSIMM

module)pin-72bit,-(321SocketSIMM

module)pin-168bit,-(642SocketDIMM

module)pin-168bit,-(641SocketDIMM

B: USB 2

FANPWR3

Row

M/IO

Multi-I/O (En/Dis)

Row 3 2

1 0

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

ISA Slot 1

ISA Slot 2

ISA Slot 3

ISA Slot 4

Board Power Input for ATX Power Supply

CPU ZIF Socket 7

Intel 430TX PCIset

BUS FREQ

FS0

FS1

FS2

CPU Voltage

VID0

VID1

VID2

VID3

CPU Fan

CacheL2

BUS Freq.

BF1

BF2

BF0 Onboard

256KB/512KB

Floppy Drives

Secondary IDE

Primary IDE

Intel PIIX4

PCIset

CR2032	(Test/Clear) RTCLR
3 Volt
Lithium Cell
BIOS Power	RTC
BIOS Power
FANPWR1

Flash ROM for BIOS

Infrared Con. (IrDA)

Panel Connections

IDE

LED

12	ASUS TXP4-X User’s Manual

Contents

Page USER’S NOTICE Product Name: ASUS TXP4-X Manual Revision: Release Date: ASUSTeK COMPUTER INC Marketing Info Technical Support ASUS COMPUTER INTERNATIONAL ASUS COMPUTER GmbH CONTENTS Page FCC & DOC COMPLIANCE Federal Communications Commission Statement •This device may not cause harmful interference, and •Re-orientor relocate the receiving antenna •Increase the separation between the equipment and receiver How this Manual is Organized Item Checklist Features of the ASUS TXP4-XMotherboard Introduction to ASUS TX97 Series of Motherboards (This page is intentionally left blank.) The ASUS TXP4-XMotherboard ASUS TXP4-XMotherboard Layout Jumpers Expansion Slots Connectors III. INSTALLATION (Map of Board) (Map of Board) Installation Steps 1. Jumpers Jumper Settings Compatible Cyrix CPU Identification III.INSTALLATION 4.CPU External (BUS) Frequency Selection (FS0, FS1, FS2) 5.CPU to BUS Frequency Ratio (BF0, BF1, BF2) (This page was left intentionally blank.) 2.System Memory (SIMM & DIMM) SIMM Memory Installation DIMM Memory Installation Procedures: 3.Central Processing Unit (CPU) 4.Expansion Cards Expansion Card Installation Procedure Assigning IRQs for Expansion Cards Assigning DMA Channels for ISA Cards 5.External Connectors 3.Parallel Printer Connector (25-pinFemale) NOTE 4.Serial Port COM1 and COM2 Connectors (Two 9-pinMale) 5.Floppy Disk Drive Connector (34-1pinFLOPPY) 7.Primary / Secondary IDE connectors (Two 40-1pinIDE) (Connectors) 8.IDE activity LED (2-pinIDE_LED) 9.Chassis , CPU , & Power Supply Fan Connectors (3-pinFANPWR) do not place jumper caps over these pins 10.IrDA / Fast IR-Compliantinfrared module connector (5-pinIR) 11.ATX Power Supply Connector (20-pinATXPWR) 12.Message LED Lead (MSG LED) 13.SMI Suspend Switch Lead (SMI) 14.ATX Power Switch / Soft Power Switch (PWR SW) 15.Reset Switch Lead (RESET) 16.System Power LED (PWR LED) Page Page Power Connection Procedures Support Software Flash Memory Writer Utility Main Menu Advanced Features Menu Managing and Updating Your Motherboard’s BIOS 6. BIOS Setup Load Defaults Standard CMOS Setup Details of Standard CMOS Setup: Time Hard Disk Drives For IDE hard disk drive setup, you can: •Use theAuto setting for detection during bootup •Enter the specifications yourself manually by using the “User” option Auto detection of hard disks on bootup Auto Drive A / Drive B (None) Floppy 3 Mode Support (Disabled) Drive A BIOS Features Setup Details of BIOS Features Setup (BIOS HDD Sequence SCSI/IDE First (IDE) IDE SCSI Boot Sequence (C,A) Video ROM BIOS Shadow (Enabled) C8000 - CBFFF Shadow to DC000 - DFFFF Shadow (Disabled) expansion cards with ROMs on them, you will need to know which addresses the ROMs use to shadow them specifically. Shadowing a ROM reduces the memory available between 640KB and 1024KB by the amount used for this purpose Chipset Features Setup Details of Chipset Features Setup 8-bitI/O Recovery Time (1 BUSCLK) Timing for 8-bitISA cards Video BIOS Cacheable (Enabled) Memory Hole at Address (None) 14MB-16MB UART2 Use Infrared (Disabled) Onboard PCI IDE Enable (Both) Primary Secondary Both Power Management Setup Details of Power Management Setup Video Off Method (DPMS OFF) PM Timers HDD Power Down Doze Standby PWR Up On Modem Act (Enabled) AC PWR Loss Restart (Disabled) Automatic Power Up (Disabled) PNP and PCI Setup Details of PNP and PCI Setup DMA x Used By ISA (No/ICU) ISA MEM Block BASE (No/ICU) SYMBIOS SCSI BIOS (Auto) Load BIOS Defaults Load Setup Defaults Supervisor Password and User Password IDE HDD Auto Detection Save & Exit Setup Exit Without Saving Desktop Management Interface (DMI) Introducing the ASUS DMI Configuration Utility System Requirements Using the ASUS DMI Configuration Utility Notes Save MIFD Load MIFD Load BIOS Defaults Symbios SCSI BIOS and Drivers Setting Up the ASUS PCI-SC200& PCI-SC860 Setting the INT Assignment for the ASUS PCI-SC200 Terminator Requirements for SCSI Devices Terminator Settings for the ASUS PCI-SC860 Terminator Settings for the ASUS PCI-SC200 SCSI ID Numbers for SCSI Devices SCSI ID Priority