Memory Features
Capacity: This telephone can store
up to 32 telephone numbers, up to 24
digits long.
One-Touch Dialing:The 16 white
spaces on the directory card are one-
touch memory locations. You can dial
one of these numbers by pressing the
memory button next to the number.
Two-Touch Dialing:The 16 gray
spaces on the directory card are two-
touch memory locations. To dial one
of these numbers you must press
, then the memory button next
to the number.
Directory Card: Remove the plastic
cover and the directory card which
is on the base. Write your telephone
numbers in the spaces provided,
and write the telephone numbers
(or names) that you want to store
in each memory location.
NOTE: You may choose to store
emergency numbers in memory
locations. This feature is provided
only as a convenience and the manu-
facturer assumes no responsibility for
customer reliance upon the memory
feature. Programming/testing of
emergency numbers should be
performed in the early morning or
late evening (off-peak) hours.
One-Touch Dialing
Storing Numbers
1Lift the handset or press .
You will hear a dial tone.
2Press and release .
3Dial the telephone number you
want to store. You will hear a beep
each time you press a button.
If you want to store a dialing
delay in the phone number,press
where the delay is needed.
Each time you press , a
three-second dialing delay is
stored in the dialing sequence.
Each three-second pause counts
as one digit; memory locations
can store up to 24 digits.
4Press and release the memory
button where you are storing the
number. You will hear two beeps
to confirm that the number has
been stored correctly.
5Hang up or press after the
number is stored correctly.
Repeat Steps 1-5 to store another
number in memory.
NOTE: Each time you complete stor-
ing a telephone number by pressing a
memory location, listen for two
quick beeps to confirm that the num-
ber has been stored in memory. If
you hear several beeps, the number
has not been stored: hang up and
start over. An extension phone “off
the hook” can interrupt program-
ming. If you still have trouble, see
“In Case of Difficulty.”
Dialing Numbers
1Lift the handset or press
and listen for a dial tone.
2Press and release a memory button.
Two-Touch Dialing
Storing Numbers
1Lift the handset or press .
2Press .
3Dial the telephone number you
want to store. You will hear a beep
each time you press a button.
If you want to store a dialing
delay in the phone number,press
where the delay is needed.
Each time you press , a
three-second dialing delay is
stored in the dialing sequence.
Each three-second pause counts
as one digit; memory locations
can store up to 24 digits.
4Press .
5Press and release the memory
button where you are storing the
number. You will hear two beeps
to confirm that the number has
been stored correctly.
6Hang up or press after the
number is stored correctly.
Repeat Steps 1-6 to store another
number in memory.
Dialing Numbers
1Lift the handset or press
and listen for a dial tone.
2Press .
3Press and release a memory button.
Storing Numbers Just Dialed
Whenever you make a telephone
call, you can store the number you
dialed without re-entering the digits
by hanging up and following the
directions for storing a number in
“One-Touch Dialing”and “Two-
Touch Dialing,”and pressing
instead of dialing the
telephone number.
Dialing Long Numbers
There are two ways to dial telephone
numbers that are too long to fit into a
memory location.
Use Two Memory Locations
You can store a number of more than
24 digits by dividing it and storing it
in two memory locations.
Follow the directions for storing
numbers in “One-Touch Dialing”and
“Two-Touch Dialing”to store the
number in two memory locations.
To dial,lift the handset or press
, listen for a dial tone, then:
• Press the memory button for the
first location (or press and
a memory button) and wait for the
dialing to stop.
• Press and release the memory but-
ton (or press and a memo-
ry button) for the second location.
Combine Manual and Memory
Dialing
Instead of using two memory loca-
tions, you might choose to store only
part of a long number. You can use
memory dialing to dial the stored por-
tion, then dial the other digits manu-
ally. If the stored portion is dialed
first, wait for dialing to stop before
you continue with manual dialing.
Erasing Numbers
To remove any number from memory,
enter another number in the same
location. To clear a memory location
and leave it empty:
1Lift the handset or press .
2Press and release .
3Press the memory (or and
a button) of the memory location
you want to clear.
MEMORY
4