*IPS-ZC1 interfaces to PA601 amplifier in IDF/MDF location. PA601 amplifier will power a single zone of up to (40) APF-15T loudspeakers set to 1 watt power tap each. This configuration will to provide up to 80dB SPL @ 50' from each APF-15T device in the zone.
ENCLOSURE IS NOT INCLUDED. Available optional enclosures:
MODEL | DESCRIPTION |
| |
SEST-IH | Surface mount, straight enclosure for IVHP, stainless steel |
| construction, neutral white finish |
| |
FEST-IH | Flush mount straight enclosure for IHVP, stainless steel |
| construction, no finish |
| |
ARCHITECT AND ENGINEER SPECIFICATIONS
Unit shall be Atlas Sound Model IHVP. The loudspeaker system shall include factory assembled horn loudspeaker, IP addressable PCB amplifier/control and cast aluminum alloy baffle. Loudspeaker shall be Atlas Sound Model APF-15. Unit shall be double re-entrant type with compression driver mounted within vandal-resistant housing. Audio power capability shall be 15 watts continuous. Frequency response shall be 600-14,000 Hz (nominal), 700-5,500 Hz (± 5 dB). Sound pressure leval shall be 104 dB (1 W / 1 M). Sound dispersion angle shall be 95°. Loudspeaker mounting shall be by eight .1875" (4.76 mm) evenly spaced holes. Model APF-15 dimension shall be 5 5⁄8" (143 mm) Dia. x 3.4375" (87 mm) Deep with 6.9375" (176 mm) Dia. flange. Finish shall be grey baked epoxy. The IP addressable PCB amplifier/control shall be mounted to the rear of the loudspeaker baffle via concealed weld studs. The amplifier/control PCB shall be capable of producing
9 watts RMS with a minimum of 9VDC power provided either locally
or via Cisco IEEE 802.3AF compliant POE switches. Interconnect shall be via female RJ-45 connector mounted to the PCB. All control functionality of the PCB amplifier shall be determined via software. The metal loudspeaker baffle overall dimensions shall be 12.88" (327 mm) wide by 14.38" (365 mm) tall. Construction shall be cast from self-aging aluminum alloy with a tensile strength of 44,000 P.S.I. Assembly shall include provisions to mount the re-entrant horn. 22-gauge perforated stainless screen shall be spot welded over the loudspeaker cut-out. Flush-mounting tamperproof heat-treated alloy screws and a special wrench shall be furnished. Dimensions shall be 10.75" (237 mm) square by .75" (19 mm) deep (not including weld stuf depth.) Baffle finish shall be textured white epoxy. Optional enclosures shall include white stainless steel surface mount model SEST-IH and flush mount model FEST-IH (unfinished.)
APF-15 LOUDSPEAKER SPECIFICATIONS | | |
| | |
Power Handling | 15 W continuous | |
| | |
Sensitivity | 120 dB at 15 W (peak) 114 dB at 15 W / 1 M (avg) 700-5,500 Hz | |
| 104 dB 1 W / 1 M (avg) 700-5,500 Hz | |
| | |
Frequency Response | 600-14,000 Hz (nominal) 700-5,500 Hz (±5 dB) | |
| | |
Dispersion | 95° (-6 dB, 2000 Hz octave band) | |
| | |
Dimensions | 5 5⁄8" Dia. x 3 7⁄16" D x 6 15⁄16" Dia. Flange | |
Finish | Grey baked epoxy | |
| | |
| | |
BAFFLE SPECIFICATIONS | | |
| | |
Baffle Material | Cast aluminum | |
| | |
Speaker Grille Material | 22-gauge perforated stainless steel | |
| | |
Overall Dimensions | 10.75" (273 mm) square x 1" (25 mm) deep | |
| | |
Color | White | |
| | |
| | |
AMPLIFIER/CONTROLLER SPECIFICATIONS | | |
| |
Power Rating | 9 watts RMS into 8 Ω load with 9VDC In |
| |
Inpute | RJ-45 female on PCB accessible from rear of baffle |
| |
Outputs | 2 wire main ± terminated to loudspeaker |
| |
Power Source | Cisco IEEE 802.3AF compliant POE network switches or local 12-18VDC PSU |
| |
Dimensions | 4.25" (108 mm) by 7.25" (184 mm) |
| |
Mounting | 4 holes to weld studs on baffle (factory assembled) |
| |
Network Control | Berbee InformaCast on multicast enabled networks |
| | |
Specifications subject to change without notice
TELEPHONE: (800) 876-3333 / FAX (800) 765-3435 | AtlasSound.com |
1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A. | |
© 2008 Atlas Sound LP | Printed in U.S.A. | 00506 | ATS002381 RevB 1/08 | SL1-2089 |
