INSTALLATION AND SET-UP FOR
Please note that the input terminal cup includes corner threaded inserts to accommodate standard four square electrical box cover (RACO #753 or equivalent). The cover allows for conduit connections directly to the input cup.
WIRE GAUGES (4 OHM OPERATION)
For very short distance speaker cable runs (less than 25') #16- Gauge, stranded, twisted pair speaker cable may be used. For speaker cable runs between 25' and 75',
WIRE GAUGES (70.7V OPERATION)
Use 18/2 stranded twisted (plenum rated if necessary per local code) for speaker cable runs up to 2000'. For distances over 2000' please consult your cable supplier for suggested wire gauges.
OVERHEAD SUSPENSION INSTALLATION
Suspension or flying speaker systems requires training and expertise. Improper rigging of a flying speaker may result in injury, death, equipment damage, and legal liability.
Installation must be carried out by fully qualified installers, in accordance with all the required safety codes and standards that are applied at the place of installation. 5:1 design factor is a generally accepted design standard, however, legal require- ments for flying vary by municipality. Please consult you local safety standards office before installing any product. We also recommend that you thoroughly check any laws and bylaws prior to installation.
If you lack the skills, training, and proper ancillary equipment to fly a speaker system do not attempt to do so.
The Atlas Sound
LOAD RATED & CERTIFIED HARDWARE (EYEBOLTS & CABLE) SHOULD BE USED IN THE INSTALLATION OF THIS PRODUCT.
These products are available from:
INSTALLATION INSTRUCTIONS
surface using the optional “C” bracket the installer must ensure that the surface is capable of safely and securely supporting the load. The hardware employed must be safely and securely attached both to the loudspeaker and the surface in question, using only the mounting holes. If you are unsure of the integrity of the mounting surface please seek assistance from architects, structural engineers or other specialists.
OMNIMOUNT™
Inserts are provided on the top, bottom and back of both models to accommodate Omnimount™ brackets. Use the Omnimount™ 30 series for the
STAND MOUNTING
The optional Atlas Sound SSA7 can be used with the top and bot- tom cabinet inserts to facilitate stand mounting for portable use.
HEARING DAMAGE
CAUTION: These professional loudspeaker systems are capable of generating very high sound pressure levels. Use care with placement and operation to avoid exposure to excessive levels that can cause permanent hearing damage.
OUTDOOR USE
The systems should not be flown or used in permanent outdoor applications under any circumstances.
FUSE PROTECTION
Units are shipped with a 20A fuse installed. This high current fuse functions as a through connection and offers no protection. If fuse protection is desired please replace the 20A fuse with a 4A fuse
WARRANTY
All products manufactured by Atlas Sound are warranted to the original dealer/installer, industrial or com- mercial purchaser to be free from defects in material and workmanship and to be in compliance with our published specifications, if any. “This warranty shall extend from the date of purchase for a period of five years on all Atlas Sound products except as follows: one year on electronics and control systems; one year on replacement parts. Additionally, fuses and lamps carry no warranty.”
ATM Group, Inc., 21000 S. Wilmington Avenue Carson, CA 90810
Tel (310)
www.atmflyware.com
Loudspeakers flown in theatres, nightclubs, conference centers or other places of work and entertainment must be provided with an independent, correctly rated and securely attached secondary safety – in addition to the principle suspension point(s). This sec- ondary safety must prevent the loudspeaker from dropping more than (6") should the principle suspension device fail.
SURFACE MOUNTING
The
of the
Atlas Sound will solely at its discretion, replace at no charge defective parts or products when the product has been applied and used in accordance with our published operation and installation instructions. We will not be responsible for defects caused by improper storage, misuse (including failure to provide reasonable and necessary maintenance), accident, abnormal atmospheres, water immersion, lighting discharge, or mal- functions when products have modified or operated in excess of rated power, altered, serviced or installed in other than a workmanlike manner. The original sales invoice should be retained as evidence of purchase under the terms of this warranty. All warranty returns must comply with our returns policy set forth below.
When products returned to Atlas Sound do not qualify for repair or replacement under our warranty, repairs may be performed at prevailing costs for material and labor unless there is indeed a written request for an estimate of repair costs before any
EXCEPT TO THE EXTENT THAT APPLICABLE LAW PREVENTS THE LIMITATION OF CONSEQUENTIAL DAM- AGES FOR PERSONAL INJURY, ATLAS SOUND SHALL NOT BE LIABLE IN TORT OR CONTRACT FOR ANY DIRECT, CONSEQUENTIAL OR INCIDENTAL LOSS OR DAMAGE ARISING OUT OF THE INSTALLATION, USE OR INABILITY TO USE THE PRODUCTS. THE ABOVE WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES INCLUDING BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICU- LAR PURPOSE.
Atlas Sound does not assume, or does it authorize any other person to assume or extend on its behalf, any other warranty, obligation or liability. This warranty gives you specific legal rights and you may have other rights that vary from state to state.
Specifications are subject to change without notice
AtlasSound.com
1601 JACK MCKAY BOULEVARD ENNIS, TEXAS 75119 U.S.A. • TELEPHONE: (800)
©2003 ATLAS SOUND LP | 00803 | ATS001614 RevA 8/03 | PP |