AIR6
In-Wall
IR Receiver
Introduction
Stand-Alone System Connections:
A: Basic System
Figure 2 shows a basic IR distribution system using the ATON AIB4 Amplified IR Connection Block, AIR6
AIR6
IR Receiver
3.Connect the
4.Install and plug the AIE1 Emitters into the AIB4.
5.Set the DIP switches to LP ON and NET ON.
6.Plug the local AIR5 IR Receiver into the IR RECEIVER jack.
7.Plug in the PS2 12VDC Power Supply.
8.IR signals sent to the AIR6s will pass through the AIB4 and control the equipment.
NOTE: Refer to the ATON AIB4 Instructions for power supply considerations and other important information.
The AIR6 features Advanced IR Filtering Technology that reduces IRI, CFL, EMI, and ESI noise sources in addition to blocking plasma TV emissions. This means that the AIR6 can be used in areas that receive substantial ambient noise such as near plasma TVs or compact flourescent lights.
NOTE: The AIR6 will take a few seconds to adjust to a given noise source. During this time, the blue Activity LED will glow brightly and then fade out. If the inter- ference disappears momentarily,then returns, the fade down process will repeat. Certain noise sources, however, (such as plasma screens) may result in
The ATON AIR6 is a small, attractively styled
Features (Refer to Figure 1)
• Stripped Leads Plus a |
• |
• IR Lens Rejects Visible Light Interference |
• Internal Crosshatch Shield Inhibits EMI/ESI Interference |
• STATUS Indicator: Green LED for System On/Off indication |
A/V Receiver |
Connection |
Terminals |
AIE2 |
Satellite |
Rear View |
AIE2 |
DVD |
ROOM 1 | ROOM 2 | ||
AIR6 |
| AIR1 | |
IR Receiver | |||
| |||
| Striped |
| |
| Side |
| |
| IR OUT | GND | |
| STATUS | +12V | |
|
|
Rear View
ROOM 3
AIR1
IR Receiver
Striped
Side
IR OUT | GND |
STATUS | +12V |
|
Connection Block |
tered, allowing most equipment to be controlled.
Limited WarrantyATON* warrants to the purchaser/end user (“you”) that the AIR6 is to be free from defects in materials and workmanship for a period of five (5) years from date of purchase (the “Warranty Period”). This warranty is transferable to subsequent owners of the product as long as the original proof of purchase is retained. If you discover a defect in material or workmanship within the Warranty Period, you can obtain warranty ser- vice by contacting ATON during the Warranty Period at
• ACTIVITY Indicator: Blue LED indicates IR signal activity |
Front | Rear | |
|
| Connection |
Decora® Style |
| Terminals |
Insert Plate |
|
|
IR Pickup |
Diode
IR Lens
4"
(102mm)
Status LED (Green)
Activity LED (Blue)
Figure 1
Specifications:
•Requires 12VDC power supply, termination block, and IR emitters for IR operation.
•Mounting: Fits in standard
•Power: +12VDC @ 6mA
•Carrier Frequency Acceptance Range: 28kHz to 90kHz
•Control Range: Up to 35 feet, depending on remote strength and ambient noise conditions
•Control Angle: +/- 50 degrees
•
•Maximum recommended cable length: 1200 feet using
•Dimensions: 4” (102mm) H x 1¼2” (38mm) W x 1” (25mm) D
PS2 |
|
|
Power |
|
|
Supply | AIB4 | AIE2 |
| Figure 2 | |
To 120V AC | Amplified IR | |
(unswitched) | ||
| Connection Block | Figure 2 |
1.Pull
2.Connect the
3. Using the provided screws, mount the AIR6 into a J
4. Set the DIP switches on the AIB4 to LP ON and NET ON or OFF.
5. Plug in the power supply.
6. IR signals sent to the AIR6 will pass through the AIB4 and control the equipment.
B: Multi-Room System
Figure 3 shows an example of multiple AIR6 IR Receivers in a
1.Pull
NOTE: MAX DISTANCE of ALL Wire Runs is 1200 ft using
2.Connect IR receivers in each room to the
Add Resistor at each IR receiver
to reduce STATUS brightness, | Wh/Blue IR |
|
Blue STATUS | To Switched | |
if desired. See text. | Brown GROUND | |
Wh/Green +12 VDC | AC Outlet | |
|
|
Connection Terminals
A/V Receiver
AIR5 |
Tabletop |
| AIE1 Emitter | PS2 |
IR Receiver |
| STATUS | |
| Satellite | Supply | |
|
| ||
|
|
| |
|
| AIE2 |
|
|
| DVD |
|
PS2 | AIB4 |
|
|
or PS3 |
|
| |
Power | Amplified IR | AIE2 | |
Supply | Connection Block |
|
|
|
|
| |
| To 120V AC |
|
|
| (unswitched) |
|
|
Figure 3
STATUS BrightnessFigure 3 also shows how an external resistor can be added to reduce the bright- ness of the Status LEDs on ATON IR receivers. In this example, a PS2 12VDC Power Supply is used as the voltage source to indicate ON/OFF status of an A/V Receiver. Choose a resistor value that achieves the brightness you desire (about 2.2k to 12k, 1/8W). Connect it in series with the STATUS lead on each IR receiver, as shown.
This warranty shall not apply to equipment (a) not manufactured by ATON, (b) to equipment which was improperly installed, (c) which was repaired or altered by persons other than ATON or its authorized repre- sentatives or subject to unauthorized tampering, alteration or modification, (d) damaged due to misuse, negligence, accident, acts of God (including, but not limited to, excess moisture, insects, lightning, flood, electrical surge, tornado, earthquake, or other catastrophic events beyond ATON’s control), or (e) subject to improper operation, maintenance or storage or unreasonable use. The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in connection with repair or replacement. The foregoing remedies shall be your exclusive remedies for any breach of warranty.
Further, the foregoing warranty does not extend to equipment sold, but not manufactured by, ATON (“Third Party Products”). With respect to any Third Party Products, the warranty for such product shall be as pro- vided by the manufacturer of such product, who will also be responsible for warranty service, and ATON will pass through to you any transferable warranty actually extended to ATON by the manufacturer.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES. ATON EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON- INFRINGEMENT. Notwithstanding the above, where applicable, if you qualify as a “consumer” under the
ATTENTION: TO OUR VALUED CONSUMERS
Valid proof of purchase is required for all warranty services. Warranty service requests made without proof of date of purchase will be denied. Please keep the original sales receipt for your records and send a copy to request warranty service.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
* ATON is a division of ELAN Home Systems, LLC.
©2007 • All rights reserved. | P/N 227948 REV:C |
1 | 2 | 3 | 4 |