Cardioid Condenser Gooseneck Microphones
Features
•Plugs into any standard XLRF-type connector, or direct mounts to 5/8"- 27 stands using included thread-mount adapter
•Low-profile element provides uniform cardioid polar pattern with 120º acceptance angle
•Superior off-axis rejection for maximum gain before feedback
•UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
•Easy-to-adjust, rugged, small-diameter, alternating gooseneck with virtually no “memory” permits quick positioning into desired shape
•UniSteep® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
•Available interchangeable elements permit angle of acceptance from 90º to 360º
• | Included low-profile isolation mount attenuates noise, shock |
| and vibration |
• | Available in five lengths |
Description
The ES915C is a wide-range miniature condenser microphone with a cardioid polar pattern. It is designed for quality sound reinforcement, professional recording, television and other demanding sound pickup applications.
The small-diameter double gooseneck design permits highly flexible positioning while maintaining a smooth, well-contoured appearance.
The ES915C is available in the following models and lengths:
•ES915C12: 304.8 mm (12.00")
•ES915C15: 381.0 mm (15.00")
•ES915C18: 457.2 mm (18.00")
•ES915C21: 533.4 mm (21.00")
•ES915C24: 609.6 mm (24.00")
The microphone requires 11V to 52V phantom power for operation.
The microphone is equipped with UniGuard® RFI-shielding technology, which offers outstanding rejection of radio frequency interference (RFI).
The microphone’s cardioid polar pattern provides a 120° angle of acceptance. Additional interchangeable elements with omnidirectional (360°), hypercardioid (100°) and MicroLine® (90°) pickup patterns are available. An XLRM-type connector insert at the base allows the microphone to be plugged directly into an XLRF-type panel jack or microphone cable.
A recessed switch permits choice of flat response or low-frequency roll- off (via integral 80 Hz high-pass UniSteep® filter) to help control undesired
engineered sound® microphones
ambient noise.
The microphone comes equipped with a two-stage foam windscreen, a low-profile isolation mount, and a stand clamp to permit attaching the microphone to a standard 5/8"- 27 or 3/8"-16 threaded mic stand or mounting flange. The microphone is enclosed in a rugged housing with a low-reflectance black finish.
Installation and Operation
The ES915C requires 11V to 52V phantom power for operation.
Output is low impedance (Lo-Z) balanced. The signal appears across Pins 2 and 3; Pin 1 is ground (shield). Output phase is “Pin 2 hot”— positive acoustic pressure produces positive voltage at Pin 2.
The microphone can be mounted on a podium or desktop with the included AT8474 low-profile isolation mount. Designed to be mounted either above or beneath the mounting surface, the AT8474 firmly secures the microphone while providing maximum attenuation of noise, shock and vibration transmitted through the mounting surface. An AT8473 stand clamp is also included to permit attaching the microphone to a standard 5/8"- 27 or 3/8"-16 threaded mic stand or mounting flange.
The provided two-stage foam windscreen simply slips over the element, effectively reducing wind noise and popping.
An integral 80 Hz high-pass UniSteep® filter provides easy switching from a flat frequency response to a low-end roll-off. The roll-off position reduces the microphone’s sensitivity to popping in close vocal use. It also reduces the pickup of low-frequency ambient noise (such as traffic, air-handling systems, etc.), room reverberation and mechanically coupled vibrations. To engage the UniSteep® filter, use the end tip of a paperclip or other small pointed instrument to slide the switch toward the “bent” line.
Avoid leaving the microphone in the open sun or in areas where temperatures exceed 110° F (43° C) for extended periods. Extremely high humidity should also be avoided.
AT8474 Isolation Mount Installation Instructions
Mounting Dimensions
A. 1.5 mm (1/16") pilot holes 3 places on 40.0 mm (1.57") circle. B. 25.4 mm (1.00") hole through the mounting surface.
C. Outside edge of mount, 52.4 mm (2.06") diameter.
CB
drawing not actual size
1.The AT8474 mount can be mounted either above or below the table surface.
2.Locate the center of the mounting location and mark it. Allow enough clearance to accommodate the AT8474 mount on the desired surface and make certain there are no physical obstructions below the desired location.
3.Locate the three mounting screw holes and mark them.
4.Using a 1" hole saw, drill the through-hole for the microphone body. (Note: Although a 1" drill bit will work, a hole saw provides for a cleaner
