AudioSource AMP 310, AMP 210, AMP 110, AMP 100, AMP 102 manual Flexibility by Design

AMP Series Products….. Value Priced Engineering Excellence!

Powerful, Flexible, Reliable.

All You Need to Bring Complete Satisfaction to Your Customer.

Speakers

AB

2

AMP210

Stereo Power Amplifier

	Power
Signal / Clip	Signal / Clip
Left	Right

5 1 5

Balance Trim		Volume Trim
Left	Right	-12dB	+6dB

34

FRONT PANEL CONTROLS

1. Power

The front panel power switch switches the AMP210/310 on or off.

2. Speaker Zone Selector

Selects active speaker output ( A or B )

3. Balance Trim

Fades speaker output between the Right and Left Channels

4. Volume Trim

Allows fine adjustment of amplifier volume.

5. Clip LEDs

Blinks red during signal clipping. Reduce volume slightly.

7

Line 1 Line 2

VSpeaker IN

Line 1R L

IN + +

6 L
R	-	-
Serial Number:		8

V

Line 2

IN OUT L

R

9

	CAUTION	AVIS			Use Class 2 Wiring
	RISK OF FIRE OR ELECTRIC SHOCK	AVIS: RISQUE DE CHOC ELECTRIQE		Minimum Impedance:		-
	DO NOT OPEN	NE PAS OUVRIR CE CARTER			8 ohm Bridged
		RESERVE AU PERSONNEL AUTORISE
	CAUTION: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE				4 ohm Stereo
	COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
	QUALIFIED PERSONNEL.
	WARNING: TO PREVENT ELECTRICAL SHOCK DO NOT REMOVE		19		Light Bar Display
	COVER. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
	QUALIFIED PERSONNEL.
Delay					On Off
			12V Trigger		Auto On
Time	Master Level	Mode
			+
3 Sec 15 Sec	Min Max Min Max	Stereo Bridged	IN - OUT		Trigger Normal	-

RL

10 11 12 13 14

		Speaker A			MODEL AMP210
R	+	+	L	-
					Custom Manufactured in China
					115V~ 60Hz 700W	18
					FUSE:T6.3AL 250V
					230V~ 50Hz 700W
					FUSE:T3.15AL 250V
	+	Bridge -
R	+	+	L	-
	Speaker B				CAUTION: See User Manual Before
15			16		Replacing Fuse
					17

REAR PANEL CONTROLS

6. Line 1 Input

A switching input that can be used if a second source is desired. Will take over when a signal is present. When there is no signal at this input the amplifier switches back to the Line 2 or “primary” input.

7. Speaker Level Input Line Select

Switches the input of the speaker level input to Line 1 or Line 2.

8. Speaker Level Input

Can be used to connect a source with speaker level output instead of line level outputs.

9. Line 2 Input/Output

The primary line level input and output for a single source connection.

10. Delay Time

Allows for a 3-15 second delay to be set and accommodate the source connected to the Line 1 input.

11. Master Level Controls

Provides independent adjustment of Left and Right channel maximum level.

12. Mode Select Switch

Switches the amplifier from Stereo mode to Bridged Mono mode

13. 12V Trigger

Allows the amplifier to be powered on by other electronics or to power on other electronics via a 3.5mm mini phone plug cable.

14. Power Mode

Set it to Normal for manual power on/off. Set to Auto-On for signal sensing. Set to Trigger when using 12V trigger for on/off.

15. Right Channel Speaker Output

Right channel terminals for speaker outputs A and B.

16. Left Channel Speaker Output

Left channel terminals for speaker outputs A and B.

17. Mains Power Inlet & Fuse Holder

Accepts IEC type line cord. A fuse located in integrated holder provides safety protection from fault conditions: replace fuse with one of same type and rating only.

18. Mains Voltage Selector

Voltage selection switch is preset to 115V (USA). For use in areas which require 230V contact your dealer. Fuse must be of type and rating marked on amplifier for use at local mains voltage.

19. Light Bar Display Control

Turns light bar display on front panel on or off. Does not control Signal/Clip LEDs or power button light ring.

Flexibility by Design!