AudioSource Powered Subwoofer owner manual PSW110, FRONT PANEL CONTROLS Figure, Placement

PSW110 / 112

OWNER’S MANUAL

PSW110

Volume Power Crossover

Protect

FRONT PANEL CONTROLS (Figure 1)

1.Volume Control Adjusts output volume.

2.Power/Protect LED indicator

Illuminates green indicating the unit is turned on while switch 10 is in “Normal” position, or when receiving signal in “Auto-On” mode. Illuminates red during standby/protect mode.

3.Variable Crossover

Sets crossover frequency between 40Hz and 200Hz. For stereo music or home theater, set the frequency to a level that sounds pleasing to your ear and the overall reproduction of your audio. If using LFE signal, set crossover to 200Hz.

Min Max 40Hz 200Hz

1 2 3

Figure 1. Front Panel

PSW110 125W 10” Powered Subwoofer			Line
4 Mode	Phase 5
			Input
		R	6
Auto On Normal	180° 0°
Speaker Level Input		L
+ L -	- R +

7

9

			6
PSW112 175W 12” Powered Subwoofer
			Line
Mode	Phase		Input
			+
		R
Auto On Normal	180° 0°
4	5	L	-

7

Speaker Level Input

LR

+

-

Power

ON

OFF

115V~ 60Hz 200W FUSE:T2.5AL 250V

230V~ 50Hz 200W FUSE:T1.25AL 250V

8 10

Figure 2. Rear Panel PSW110

REAR PANEL CONTROLS (Figures 2-3)

Figure 3. Rear Panel PSW112

9

Power

115V~ 60Hz 300W	OFF ON
FUSE:T4AL 250V
230V~ 50Hz 300W
FUSE:T2AL 250V
8	10

4.Power Mode

Sets the power-on/off option of the PSW110/112. Set it to Normal for manual control using switch 10 . Set switch to Auto-On for automatic power-on when signal is present; after 10 minutes with no signal, unit will enter standby mode. For Auto-On the power switch is left in “ON” position.

5.Phase Control

Normally set to 0°. In rare instances, due to your unique sound system or the size of your room, the output may be out of phase. If the sound is hollow or the volume knob has little effect, set to 180° to compensate for these factors.

6.Line Level Input

Connect to the line level, subwoofer, or LFE output of your receiver, pre-amp, or power amp. Do not use if Speaker Level Inputs are connected. For single mono input: plug into either R or L terminal, or use a y-adaptor.

7.Speaker Level Input

Use when line level outputs are unavailable from your receiver, pre-amp or power amp. Your existing stereo speakers can share these terminals, allowing you to add bass to any stereo or home theater system. Always maintain speaker polarity by connecting positive (+) and negative (-) terminals on this unit with corresponding terminals on your existing speakers and source. Do not use if Line Level Inputs are connected.

8.Mains Power Inlet & Fuse Holder

Accepts IEC type line cord. A fuse located in the integrated holder provides safety from fault conditions: replace fuse with one of same type and rating only.

9.Mains Voltage Selector

Voltage selection switch is preset to 115V (USA). For use in areas which require 230V contact your dealer. Fuse must be of type and rating marked on amplifier for use at local mains voltage.

10.Power Switch

Turns unit on and off in Normal power mode. Leave set to “ON” when using Auto-On power mode.

PLACEMENT

This unit features removable feet, a front firing woofer and ports, and front panel controls for ease of use in a cabinet. The bass output of this unit is omnidirectional so this unit may be placed anywhere in the listening environment. Walls or corners will help reflect the bass for fuller sound. During use unit will vibrate: care should be taken not to place any liquids or heavy items such as drinks or houseplants on top as they may fall and damage your house or this subwoofer.

9200 North Decatur St. Portland, OR 97203 • 503.286.9300 • www.audiosource.net 3