SM4-800 / SM4-1000 / 4 CHANNEL AMPLIFIER APPLICATIONS
4 CHANNEL FULL RANGE SYSTEM
Here we show how to use the 4 channel amplifiers as straight forward discrete 4 | Channels 3/4: |
channel full range units. | - HI PASS: N/A |
Interconnect cable checklist: | - LOW PASS: N/A |
| |
- Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables. | Level control checklist: |
Switch setting checklist: | - Refer to the section “Setting up systems after installation for best performance” |
| |
- 1/2CH | Minimum final loudspeaker impedances: |
- 3/4CH | - |
FULL RANGE
Crossover frequency control checklist: |
|
|
| SPEAKERS |
Channels 1/2: |
|
|
| |
|
|
|
| |
- HI PASS: N/A |
|
|
|
|
- LOW PASS: N/A |
|
|
|
|
|
|
|
|
FULL RANGE
STEREO LINE
INPUTS
| CH3/4 |
| L |
|
|
|
|
|
|
|
|
| LINE |
| |
| CH1/2 |
|
|
|
| INPUT |
|
| CH1 |
| + - g | HI IN |
| CH3 |
|
| H2 |
| - + | UT | - + | CH4 |
|
| 5V 0.2V |
| LEVEL |
| 5V 0.2V | LEVEL |
|
CHANNEL 1 / 2 | 0dB 12dB 60Hz 1.2KHz |
| BASS EQ HPF |
| 0dB 12dB 60Hz 1.2KHz | BASS EQ HPF | CHANNEL 3 / 4 |
| 30Hz 250Hz |
| LPF |
| 30Hz 250Hz | LPF |
|
| FULL LPF HPF |
| FULL LPF HPF |
| |||
| LINE |
|
| CHANNEL | 2 3 4 | MODE |
|
| OUTPUT | L |
|
| R |
|
|
| OUTPUT | LEF |
| 3/4SPEAKER | RIGHT |
|
| + |
| CH | - |
FUSE |
|
|
POWER INPUT | GND REM +12V |
|
| OUTPUT | - |
| ½ SPEAKER | LEFT |
| RIGH | |
| CH |
|
| POWER | PROTECT |
B IDGE
B IDGE
TO BATTERY + 12 Volts VIA FUSE
REMOTE
CHASSIS GROUND
2 or 3 CHANNEL FULL RANGE SYSTEM
Here we show how to use the 4 channel amplifiers as full range 2 or 3 channel units by taking advantage of the mono bridging capability of all Autotek amplifiers.
The following example shows how to create a 3 channel system by mono bridging channel pair 3 / 4. In order to create a 2 channel system, simply follow the example to also mono bridge channel pair 1 / 2.
Interconnect cable checklist:
- Connect the inputs of channel pair 1/2 to a suitable stereo source, e.g. a head unit |
with good quality RCA cables. |
- A MONO signal source is required to bridge channel pair 3/4, such as would be |
available from the mono sub bass output of an active crossover, whether |
standalone, or built into a head unit or equalizer. |
Important: Do not be tempted to connect the hot, or positive outputs, from any |
source together to obtain a mono signal, as this could very well damage the output |
stage of that source. |
Crossover frequency control checklist:
Channels 1/2:
-HI PASS: N/A
-LOW PASS: N/A
Channels 3/4:
-HI PASS: N/A
-LOW PASS: N/A
TIP: If you are using the mono sub bass output of an active crossover, there is nothing wrong with switching in the low pass filter in these amplifiers for a steeper low pass rolloff.
Level control checklist:
-Refer to the section “Setting up systems after installation for best performance”
- It is necessary to feed the SAME signal to both left and right inputs via a |
RCA cable. |
- Connect the mono speaker positive terminal to the LEFT +, and its negative |
terminal to RIGHT - as shown. |
Switch setting checklist:
-1/2CH
-3/4CH
Minimum final loudspeaker impedances:
-
-
MONO
OR SUB BASS
SPEAKER
STEREO
FULL RANGE
1STEREO
1MONO FULL RANGE LINE INPUTS
| CH3/4 |
| LL |
|
|
|
|
|
|
|
|
| LINE |
| |
| CH1/2 |
|
|
|
| INPUT |
|
| H1 CH2 |
| - gnd- + | I INPUT | - gnd- + | CH3 CH4 |
|
| 5V 0.2V |
| LEVEL |
| 5V 0.2V | LEVEL |
|
CHANNEL 1 / 2 | 0dB 12dB 60Hz 1.2KHz |
| BASS EQ HPF |
| 0dB 12dB 60Hz 1.2KHz | BASS EQ HPF | CHANNEL 3 / 4 |
| 30Hz 250Hz |
| LPF |
| 30Hz 250Hz | LPF |
|
| FULL LPF HPF |
| FULL LPF HPF |
| |||
| LINE |
|
| CHANNEL | 2 3 4 | MODE |
|
| OUTPUT | L |
|
| R |
|
|
| OUTPUT | LEFT |
|
| - |
| 3/4CHSPEAKER | - |
| RIGHT | |
|
| + |
FUSE |
|
|
POWER INPUT | GND REM +12V |
|
| OUTPUT | EFT - |
| ½ SPEAKER | IGHT+ - |
| CH | - |
| POWER | PROTECT |
BRIDGED
B IDGED
TO BATTERY + 12 Volts VIA FUSE
REMOTE
CHASSIS GROUND
OR HIGHS
SPEAKERS
5