OSD MENU | Description |
|
|
SENSOR | SETUP |
|
| |
SENSOR | REC | TIME | 010 | SEC |
ALARM | OUT | TIME | 010 | SEC |
CHANNEL - 1 |
| NOT | INSTALLED | |
CHANNEL - 2 |
| NOT | INSTALLED | |
CHANNEL - 3 |
| NOT | INSTALLED | |
CHANNEL - 4 |
| NOT | INSTALLED |
SENSOR REC TIME :
Set the amount of time (in second) to start record when the sensor has triggered
ALARM OUT TIME :
Set the amount of time (in second) to continue sending the alarm once triggered
CHANNEL 1~4 :
Customize the initial state of the attached sensor. Refer to the table below to customize the sensor state
|
|
|
|
|
|
|
| Condition |
|
| Description |
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| NOT INSTALLED |
| Indicates that there is no sensor connected |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| NORMAL OPEN |
| Indicates that the initial state of the sensor is |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| normal open. Video recording initiates when |
| ||||
|
|
|
|
|
|
|
|
|
|
|
| there is a changes in the sensor state |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| NORMAL CLOSE |
| Indicates that the initial state of the sensor is |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| normal close. Video recording initiates when |
| ||||
|
|
|
|
|
|
|
|
|
|
|
| there is a changes in the sensor state |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MOTION | SETUP |
|
|
|
|
| MOTION | CAMERA : |
|
|
|
| ||||
| MOTION | CAMERA | 1 | 2 | 3 | 4 |
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||
| SENSITIVITIY | L |
|
|
|
| Enable/disable the channel number to detect motion. | ||||||||||
| MOTION | RECORD TIME 010 | SEC |
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| SENSITIVITY : |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| Set the sensitivity level. The sensitivity is from H (High), | |||||||||
|
|
|
|
|
|
|
| 9~ 2 and L (Low). |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| MOTION | RECORD TIME : |
|
|
|
| ||||
|
|
|
|
|
|
|
| Set the amount of time (in second) to record when | |||||||||
|
|
|
|
|
|
|
| motion is detected. |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| NETWORK SETUP |
|
|
|
|
| NETWORK SETUP: |
|
|
|
| ||||||
| IP MODE |
| STATIC |
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| NW ENABLE | 1 | 2 | 3 | 4 |
| Setup | the | network parameters for the | internet or | |||||||
| VIDEO PORT | 5001 |
|
|
|
| |||||||||||
|
|
|
|
| intranet remote monitor or playback. |
|
|
|
| ||||||||
| UPGARDE PORT | 5005 |
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
| IP MODE: |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| The system provides 3 types of IP setup mode – Static, | |||||||||
|
|
|
|
|
|
|
| DHCP, and PPPOE. |
|
|
|
| |||||
|
|
|
|
|
|
|
| Use | ▲ | and | ▼ buttons to go up and down and | ||||||
|
|
|
|
|
|
|
| select IP MODE, and then press |
| . Use | ▲ | and | |||||
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
| ▼ | buttons to | change the selections | and | press | |||||
|
|
|
|
|
|
|
|
or
▼
to make a selection.
STATIC: Assigns a constant IP address for the
DVR system. Use ▲ and ▼ buttons to go up and down and select items, and then press
or
▼
to make selection. Use
▼
and
▼
to move left and right to select or enter the configuration value.
-IP ADDRESS: Assign a constant IP address which a real IP addresses give from ISP to DVR system.
-SUBNET: It is a bitmask used to identify the sub network and how many bits provide room for
18