Axis Communications AXIS 83+, AXIS 82+ manual More information developer.axis.com

AXIS 82+ Developer Board / AXIS 83+ Device Server

Technical Overview

•Product-ready device server platform based on the AXIS ETRAX 100LX MCM 4+16 chip. The product ships with a pre-installed Linux operating system and pre-programmed Ethernet address. Full source code is available for all applications and drivers at developer.axis.com

Ethernet Network Connection

• Primary Physical network connection on

10BaseT Ethernet or 100BaseTX Fast Ethernet

networks using RJ45 twisted pair cable

• Secondary Physical network connection on

10BaseT Ethernet or 100BaseTX Fast Ethernet,

but limited in speed to 12 MBit/s since it

is connected through an internal USB port.

Actual routing speed is 4.5 MBit between the

RS485/422 Terminal Block

•One RS485/422 serial port supported on a single screw terminal block. Supports baud rates up to 1843200 bps

Pinout:

1AC Power

2 AC Power

3 GND

4RS422 GND

Connected to GND through 100 ohm resistor

5RX/TX-AUse pin 5 and 6 for 2-wire RS-485

6 RX/TX-BUse pin 5 and 6 for 2-wire RS-485 7 TX-

8 TX+

Operating Environment

•Temperature: +5°C to +50°C

•Humidity: 8-80% RHG, non-condensing

Product Warranty

•A one-year warranty is included

The specifications below are appropriate to the AXIS 83+ Device Server (supplied with aluminum casing) only

Mechanical Design

•A stable aluminum casing that can be conveniently mounted on a wall (mounting brackets are included)

two interfaces

Serial Connection

•Two RS232 serial ports terminated with 9 pin MALE D-SUB connectors, both ports support RXD, TXD, RTS, CTS, DSR, DTR, RI (not on COM1) and CD at baud rates up to 115200 bps

Pinout:

1	CD	Carrier detect	(Input)
2	RxD	Receive Data	(Input)
3	TxD	Transmit Data	(Output)

Parallel port & General purpose I/O

•An onboard I/O port, located on pin headers, can be used as either a standard parallel data port, or as a general purpose I/O control port

USB 1.1 Port

•Compliant USB 1.1 (host) port for connection to USB cameras, Barcode scanners, Bluetooth, WiFi, etc.

•The port can provide +5.0 VDC, 500 mA to the device

Metrics

•Height: 41 mm

•Width: 140 mm

•Length: 118 mm

•Weight: 420 g

Product Identification

•Sticker label on the underside, which identifies the unit as an AXIS 83+ and also identifies the Ethernet address of the unit

4	DTR	Data Terminal Ready	(Output)
5	GND	Ground
6	DSR	Data Set Ready	(Input)
7	RTS	Request To Send	(Output)
8	CTS	Clear To Send	(Input)
9	RI	Ring Indicator	(Input)

•One additional serial port is located on pin headers on the board and may be used for debugging

Application Flash-loading

•The customer’s Linux application can be flash loaded to the Device Server Platform over the network using FTP (File Transfer Protocol)

Hardware

•CPU: 32 bit RISC processor (AXIS ETRAX 100LX MCM 4+16)

•Flash memory: 8 Mbytes (4.5 Mbytes available for applications in default configuration).

•RAM: 32 Mbytes

Power Supply

•Power: 9-24 VAC (or DC), 9.6 VA, via external power supply (included) or on screw terminal block

•Power consumption typically between

2.8 VA and 3.2 VA. With load on USB Vbus, between 5.0 VA and 7.2 VA

Approvals*

•AXIS 83+ Device Server compliant with both industrial and light industrial/commercial EMC standards for both emission and immunity

•Immunity Standards: EN 55024:1998

EN 61000-6-2:2001 EN 61000-6-1:2001

•Emission Standards:

EN 55022:1998+A1 Class B (CISPR 22:1997+A1, Class B) FCC Part 15, Subpart B, Class A FCC Part 15, Subpart B, Class B EN 61000-3-2:2000

EN 61000-3-3:1995+A1

•Safety:

EN 60950, UL (US version).

*The approvals are made with the aluminum casing and cannot be guaranteed when the PCB is not mounted in a similar box

24735/EN/R2/0505

More information: developer.axis.com

©2003 Axis Communications AB. The Axis Communications logotype is a registered trademark of Axis Communications AB.

All other company names and products are trademarks or registered trademarks of their respective companies. We reserve the right to introduce modifications without notice