![](/images/new-backgrounds/1058789/587895x1.webp)
STANDARD | SCOPE |
|
|
B.S. 6891 | Gas Installation. |
B.S. 5440: Pt 1 | Flues. |
B.S. 5440: Pt 2 | Air Supply. |
|
|
B.S. 5546 | Installation of hot water supplies |
| for domestic purposes. |
|
|
B.S. 7074 | Expansion vessels and ancillary |
| equipment for sealed water systems. |
|
|
B.S. 5449 | Forced circulation hot water systems. |
B.S. 6798 | Installation of gas fired hot water |
| boilers. |
“Benchmark” Installation, Commissioning and Service Record Log Book
Please ensure that your installer has completed the Installation and Commissioning sections of the Log Book and hands the Log Book over. The details of the Log Book will be required in the event of any warranty work. Keep the Log Book in a safe place and ensure that the relevant sections are completed at each subsequent regular service visit.
All CORGI registered installers carry a CORGI identification card and have a registration number. Both should be recorded in your boiler Log Book. You can check your installer is registered by telephoning 01256 372300 or writing to:-
1 Elmwood,
Chineham Business Park, Crockford Lane, Basingstoke.
RG24 8WG.
IN AN EMERGENCY
If a water or gas leak occurs or is suspected, the boiler can be isolated at the inlet valves as follows;
1.Turn off the electrical supply and turn the selector switch on the facia box to the OFF position.
2.Using a suitable open ended spanner or screwdriver turn the square on the gas tap to the left to isolate the gas supply at the boiler (Fig. 1).
3.The isolating valves are positioned under the boiler and can be closed by turning their taps to the right towards the wall (Fig. 2).
4.Call your Service Engineer as soon as possible.
1.0Warnings
1.1Safe Installation
1.The appliance is suitable for installation only in G.B. and I.E. and should be installed in accordance with the rules in force. For Ireland install in accordance with I.S.813 “INSTALLATION OF GAS APPLIANCES”. The installation must be carried out by a CORGI Registered Installer or other registered competent person and be in accordance with the relevant requirements of GAS SAFETY (Installation and Use) REGULATIONS most recent edition, the BUILDING REGULATIONS issued by the Department of the Environment, BUILDING STANDARDS (Scotland) (Consolidation) REGULATIONS issued by the Scottish Development Department and the LOCAL BUILDING REGULATIONS. Where no specific instructions are given, reference should be made to the relevant
BRITISH STANDARD CODES OF PRACTICE and INSTALLATION SPECIFICATIONS.
2.This appliance must be installed in accordance with the manufacturer’s instructions and the rules in force, and only used in a suitably ventilated location.
3.Read the instructions before installing or using this appliance.
4.Any purpose provided ventilation should be checked periodically to ensure that it is free from obstruction.
IMPORTANT - The addition of anything that may interfere with the normal operation of the appliance without the express written permission of Baxi UK Limited could invalidate the appliance warranty and infringe the GAS SAFETY (Installation and Use) REGULATIONS.
1.2In case of gas leaks
1.If a gas leak is found or suspected, turn off the gas supply at the meter immediately and at the isolating valve on the boiler if possible. Contact your Installer or Transco (under 'Gas' in the phone directory).
Gas Tap
Fig. 1
Fig. 2
Heating Flow, Heating Return
and Mains Water Inlet
1.3Servicing your Appliance
1.For reasons of safety and economy your appliance should be serviced annually. Servicing must be performed by a competent person. Your Installer or British Gas Service will be able to advise you.
1.4Electricity Supply
1.THIS APPLIANCE MUST BE EARTHED.
2.A standard 230V ~ 50Hz supply is required. The appliance must be protected by a 3 amp fuse.
Never Hang Flammable Items Over The
Appliance
Isolating Valves
3