![](/images/new-backgrounds/1028850/288509x1.webp)
During an adjustment session each parameter may be checked or changed at any time in the following way:
PARAMETER | USER'S ACTIONS |
|
|
|
|
|
|
|
|
|
| |||
KEY |
|
|
|
|
|
|
|
|
|
|
|
| ||
CHECK | Press the Key (5,6,7,8,11) corresponding to the parameter to be checked and then press the CHECK VALUES Key | |||||||||||||
VALUES | (9). |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| Count the number of times the green LED flashes, which correspond to the value of the checked parameter. No | |||||||||||
|
|
| green LED flash corresponds to the value 0. | |||||||||||
|
|
| Repeat this operation to check the value of the other parameters if required. | |||||||||||
|
|
| Example: SENSITIVITY Key (6) – 7 flashes of the green LED: the sensitivity is set at the value 7. | |||||||||||
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CHECK VALUES: |
|
|
|
|
|
| X |
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| PLUS | Press the Key (5 or 6) corresponding to the hold time or sensitivity parameter to be modified | ||||||||||||
|
|
| ||||||||||||
|
|
| ||||||||||||
|
|
| and then press the PLUS Key (2) to increase the value by 1 unit. | |||||||||||
|
|
| PLUS: |
| X |
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MINUS | Press the Key (5 or 6) corresponding to the hold time or sensitivity parameter to be modified. | |||||||||||||
|
|
| ||||||||||||
|
|
| and then press the MINUS Key (4) to reduce the value by 1 unit. | |||||||||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
| MINUS: |
| X |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
During a sensor adjustment session all the parameters may be reset to their factory values in the following way:
PARAMETER | USER'S ACTIONS |
|
|
| |||
KEY |
|
|
|
|
| ||
DEFAULT | Press the DEFAULT VALUES Key (12), then press the NUMBER Key 1. All the parameters are reset to the | ||||||
VALUES | factory values (see below). |
|
|
| |||
|
|
| DEFAULTS VALUES: |
|
|
|
|
|
|
|
|
| 1 |
| |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
PARAMETER KEY | USER'S ACTIONS | |||||||
|
|
|
|
|
|
|
| |
SENSITIVITY | Press the SENSITIVITY Key (6). | |||||||
|
|
| Use the NUMBER Keys | |||||
|
|
| ||||||
|
|
| required (or adjust this sensitivity using the PLUS (2) or | |||||
|
|
| MINUS (4) keys as explained above) | |||||
|
|
| SENSITIVITY: |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
HOLD TIME | Press the HOLD TIME Key (5). | |||||||
|
|
| Use the NUMBER Keys | |||||
|
|
| time (0.5 s to 9 s) | (or adjust this parameter using the PLUS | ||||
|
|
| (2) or MINUS (4) keys as explained above). | |||||
|
|
| HOLD TIME: |
|
|
|
| |
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
RELAY | Press the RELAY CONFIGURATION Key (11). | |||||||
Use the NUMBER Keys | ||||||||
CONFIGURATION | configuration: |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
FACTORY
SETTING
7
0.5 s
1
(Active
Output)
LED SIGNAL
The red LED flashes quickly waiting for the value.
Once this has been entered, it flashes slowly again.
The red LED flashes quickly waiting for the value.
Once this has been entered, it flashes slowly again.
The red LED flashes quickly waiting for the value.
Once this has been entered, it flashes slowly again.
75.5351.02 EN 20080317 (75.5350) | Page 5 of 7 |