Beckett

Instruction Manual – Model AFII Oil Burner

Prepare before installing

Verify specifications

Capacity

“HLX” heads

 

Firing rate ..……..……………....…... 0.40 – 1.50 GPH

 

Input ..………..….…………… 56,000 – 210,000 Btu/h

 

 

 

“FBX” heads

 

Firing rate ..…..……………………… 0.40 - 1.35 GPH

 

Input ..………….…..………….56,000 – 189,000 Btu/h

Fuels

U. S. …. No. 1 or No. 2 heating oil only (ASTM D396)

 

Canada ….... No. 1 stove oil or No. 2 furnace oil only

Electrical

Power supply ....…….... 120 VAC/60 Hz/single phase

 

Operating load ……….… 5.8 Amps maximum; Note 1

 

Motor …..……… ……………………..1/7 hp, 3450 rpm

 

……….……...…… rotation CW when facing shaft end

 

Ignition .……... Continuous duty iron-core transformer

 

OR ………..... Continuous duty solid state igniter

Fuel unit

Outlet pressure ………..…..……………………. Note 2

Air tube

ATC code ……………………….. See Table 1, page 2

Dimensions

Height (maximum) ……….…….….…………13 inches

 

Width (maximum) ………….………..….. …..14 inches

 

Depth (chassis only) ………….……….6-11/16 inches

 

Air tube diameter ………………………….3 ½ inches

 

 

Note 1. A burner with an electronic igniter will have a lower operating current. The actual load should be determined by a current meter.

Note 2. See appliance manufacturer’s burner specifications for recommended outlet pressure. Pressure is 140 psig unless otherwise noted.

Be aware of hazard definitions

DANGER

Denotes presence of a hazard which, if ignored, will result in

severe personal injury, death, or substantial property damage.

 

Denotes presence of a hazard which, if ignored, could result in

WARNING

severe personal injury, death, or substantial property damage.

CAUTION Denotes presence of a hazard which, if ignored, could result in minor personal injury or property damage.

NOTICE

Intended to bring special attention to information, but not

related to personal injury or property damage.

Check certifications/approvals

Underwriters Laboratories has certified this burner to comply with ANSI/UL 296 and has listed it for use with #1 or #2 fuel oil as specified in ASTM D396. Low sulfur #1 and #2 fuel oils reduce heat exchanger deposits with all burners compared to the standard fuels. Reduced deposits extend the service interval for cleaning and improve the efficiency of the appliance over time. Low sulfur fuels reduce particulate and oxides of nitrogen emissions as well. The Oilheat Manufacturers' Association recommends these fuels as the preferred fuels for this burner.

State and local approvals are shown on burner rating label (see below).

All oil burners should be installed in accordance with regulations of the latest revision of the National Fire Protection Association Standard NFPA 31 and in complete accordance with all local codes and authorities having jurisdiction. Regulation of these authorities take precedence over the general instructions provided in this installation manual.

For recommended installation practice in Canada, refer to the latest version of CSA Standard B139.

Notice special requirements

DANGER This equipment must be installed, adjusted and started only

by a qualified service agency – an individual or agency, licensed and experienced with all codes and ordinances, who is responsible for the installation and adjustment of the equipment. The installation must comply with all local codes and ordinances and with the latest revision of the National Fire Protection Standard for Oil-Burning Equipment, NFPA 31 (or CSA B139).

WARNING

Read all instructions before proceeding. Follow all

instructions completely. Failure to follow these instructions could result in equipment malfunction, causing severe personal injury, death or substantial property damage.

NOTICE Concealed damage — If you discover damage to the burner or controls during unpacking, notify the carrier at once and file the appropriate claim.

NOTICE When contacting Beckett for service information — Please record the burner serial number (and have available when calling or writing). You will find the serial number on the silver label located on the top right of the burner, to the left of the air dial. See illustration below.

SK9642

3

Page 3
Image 3
Beckett 150, AFII 85, 100 instruction manual Prepare before installing, Verify specifications, Be aware of hazard definitions

150, 100, AFII 85 specifications

Beckett AFII 85, 100, and 150 are advanced air filtration models designed to enhance indoor air quality while ensuring maximum energy efficiency. These units are particularly suitable for both residential and commercial applications and offer a robust solution to combat air pollution, allergens, and other harmful particles.

One of the cornerstone features of the Beckett AFII series is its multi-stage filtration system. Each model comes equipped with a pre-filter that captures larger particles, effectively prolonging the life of the primary HEPA filter. The HEPA filter is capable of trapping 99.97% of airborne particles as small as 0.3 microns, including dust, pollen, pet dander, and smoke. This high filtration efficiency ensures that the air circulating in your environment is clean and healthy.

Technology integration is another key attribute of the Beckett AFII models. These units utilize advanced airflow technology which optimizes the volume of air that passes through the filters while minimizing energy consumption. The aerodynamic design of the fan impeller aids in reducing noise levels, allowing for a quieter operation compared to traditional air filtration systems.

The Beckett AFII series is also designed with user convenience in mind. Each model is equipped with a user-friendly interface that allows for easy adjustments to the fan speed and timer settings. An integrated filter change indicator alerts users when it's time to replace the filters, ensuring optimal performance at all times.

The construction of these units is robust, featuring high-quality materials that promise durability and longevity. They are designed to be easy to install and maintain, accommodating various settings and requirements.

Additionally, the design of the Beckett AFII 85, 100, and 150 models is sleek and modern, making them suitable for integration into diverse interior styles without compromising aesthetic appeal.

In summary, the Beckett AFII 85, 100, and 150 air filtration systems combine advanced filtration capabilities, energy-efficient operation, and user-friendly features, making them ideal choices for anyone looking to improve indoor air quality. With their commitment to performance and reliability, these models represent a valuable investment in health and well-being.