PRO MIXER DX626
The BOOTH output gives you another possible way to connect an amplifier. It is controlled by the BOOTH control on the front panel. Through this output you can operate monitor speakers or even provide another area with sound.
The MASTER output is for connecting an amplifier and is adjusted using the MASTER control.
+Always turn the power amps on last to avoid inrush currents that can easily damage your speakers. And, to avoid sudden and unpleasant surprises for your ears, make sure there is no signal at the DX626 before turning on the power amps. To be sure, slide all the faders to the bottom and switch all controls to zero.
This is the connector for the power cable. This is where the advantage of the sophisticated internal power supply can be seen: the pulse behaviour of each amplifying circuit is mainly determined by the voltage reserves available. Each mixing console is equipped with numerous operational amplifiers (op amps) to process line level signals. Due to limited output of their power supplies, many mixing consoles show signs of “stress” when subjected to heavy loads. But not your DJX400: the sound is always clear and transparent.
FUSE HOLDER / VOLTAGE SETTING. Before connecting the unit to the mains, ensure that the voltage setting matches your local voltage. Blown fuses should only be replaced by a fuse of the same type and rating. On some units, the fuse holder can be switched to one of two positions, i.e. 230 V and 115 V. N.B: should you desire to operate the unit outside Europe at 115 V, a higher fuse rating is required.
PRO MIXER DX626 SERIAL NUMBER. Please take the time to complete and return the warranty card within 14 days of the date of purchase. Or, simply register online at www.behringer.com.
3. SPECIFICATIONS
AUDIO INPUTS |
|
|
Mic | 40 dB Gain, elec. balanced input | |
Phono 1, 2 and 3 | 40 dB Gain @ 1 kHz, unbalanced | |
| inputs |
|
Line 1, 2 and 3 | 0 dB Gain, unbalanced inputs | |
AUDIO OUTPUTS |
|
|
Master | max. +21 dBu @ +10 dB (Line In) | |
Booth | max. +21 dBu @ +10 dB (Line In) | |
Tape | type. 0 dBu Phones | |
| type. 125 mΩ @ 1% THD | |
EQUALIZER |
|
|
Stereo Low | +12 | |
Stereo Mid | +12 | |
Stereo High | +12 | |
Mic Low | +12 | |
Mic Mid | +12 | |
Mic High | +12 | |
TALKOVER BUTTON (MIC) |
|
|
LAMP (BNC) | 12 V/400 mA |
|
GENERAL |
|
|
|
|
|
ratio (S/N) | > 87 dB (Line) |
|
Crosstalk | > 70 dB (Line) |
|
Distortion (THD) | < 0.05% |
|
Frequency response | 20 Hz - 20 kHz |
|
Gain control range |
|
|
POWER SUPPLY |
|
|
Mains Voltage | USA/Canada | 120 V ~, 60 Hz |
| U.K./Australia | 240 V ~, 50 Hz |
| Europe | 230 V ~, 50 Hz |
General |
|
|
Export Model | ||
Power Consumption | max. 15 W |
|
Fuse | 100 - 120 V ~: T 500 mA H | |
| 200 - 240 V ~: T 315 mA H | |
Mains Connection | Standard IEC Receptacle | |
DIMENSIONS/WEIGHT |
|
|
Dimensions |
|
|
(H x W x D) | approx. 2.4"/3.6" (61 mm/91 mm) | |
| x 10" (254 mm) |
|
| x 12" (305 mm) |
|
Weight | approx. 2.4 kg |
|
BEHRINGER makes every effort to ensure the highest standard of quality. Necessary modifications are carried out without notice. Thus, the specifications and design of the device may differ from the information
given in this manual.
3. SPECIFICATIONS | 7 |